Search

Search: Search took 1.00 seconds.

  1. Replies
    12
    Views
    659

    You adjust the pump by adjusting the cable end....

    You adjust the pump by adjusting the cable end. Just like you would adjust the the free play in the throttle cable. Shorten or lengthen the cable adjuster till the marks line up.
  2. Replies
    12
    Views
    659

    Yes that is the correct cable number. However I'd...

    Yes that is the correct cable number. However I'd check it before ordering. It may have just come loose or off.
    Also when you figure out what is wrong if it's involves the cable you'll need to set...
  3. Stay away from sbt! There quality sucks at best...

    Stay away from sbt! There quality sucks at best for a complete motor. I buy there parts and supplies but not a motor.
    Try "pwcengines". Comparable pricing and warranty to sbt and much better...
  4. Replies
    22
    Views
    2,072

    https://youtu.be/6mW_gzdh6to Here a very good...

    https://youtu.be/6mW_gzdh6to

    Here a very good video on the importance of having the correct trailer tongue weight. And trailer weight balance.
  5. Replies
    19
    Views
    1,677

    2-Stroke If your going to rebuild it be sure to at least...

    If your going to rebuild it be sure to at least flush out the lower end if you don't pull apart and reseal. That piston left debris all over inside. Pull the intake and clean the reeds as well. ...
  6. Replies
    8
    Views
    1,111

    Watercraft super store. $29 Google: EZ throttle...

    Watercraft super store. $29
    Google: EZ throttle jet ski.
    I'm going to order 1 myself.
  7. Replies
    7
    Views
    509

    I don't know for a fact but your probably...

    I don't know for a fact but your probably correct. The only change would be the orifice in the seat. The needle would just set a tick deeper in the seat as the orifice gets bigger. 1.2 vs 1.5 and so...
  8. Replies
    5
    Views
    753

    No, you don't have to run only yamalube. You can...

    No, you don't have to run only yamalube. You can run any oil marked tc-w3.
    Pennzoil makes a good synthetic. And you can buy it at Walmart. I use it in all my boat motors. Injected and pre-mix.
    In...
  9. Replies
    9
    Views
    913

    I'm not sure who has a green oil. I'll check next...

    I'm not sure who has a green oil. I'll check next weekend when I'm back at my lake house as to the color of the Pennzoil I use in my boats. Never really look at color.
  10. The nice thing with the valve you can turn it on...

    The nice thing with the valve you can turn it on and off when need be. Around the holidays here on the lake it's very busy and I like it on for added visibility.
  11. Good call, if they don't care enough to keep it...

    Good call, if they don't care enough to keep it clean. You can be guaranteed the maintenance isn't any better.
  12. Replies
    3
    Views
    567

    I'm betting the carbs on at least the xl were...

    I'm betting the carbs on at least the xl were rebuilt when the motor was done.
    I'd drain the old fuel and run a couple tanks of carb cleaner through them then decide whether they need rebuilt.
    As...
  13. Replies
    22
    Views
    1,352

    Sorry, don't be upset if answers don't come for a...

    Sorry, don't be upset if answers don't come for a bit. Holiday weekends especially. If your not working the weekend like me your out riding.
    Any how if this is untouched you have a lot of TLC to...
  14. Replies
    18
    Views
    1,465

    James, I've seen the valve go out the exhaust...

    James,
    I've seen the valve go out the exhaust to many times. It blows my mind that at 6000/7000 rpm that it happens and does not destroy the motor. I pulled my 800 apart late winter this year to...
  15. Replies
    3
    Views
    823

    how to keep your pisser holes clear

    All,
    I've found that the foam ear plugs work very well to keep the bugs,wasps and spiders out of the pisser hole on my ski during storage. if you get the corded ones you can also tie on a ribbon so...
  16. Replies
    9
    Views
    1,163

    If it's a ghost spot and they are using newer...

    If it's a ghost spot and they are using newer water based paints as suspect they are, then it could be the base coat wasn't cured out properly before they clear coated and sealed in moisture. Spot...
  17. Replies
    9
    Views
    1,163

    Just curious, have you said anything to dealer?...

    Just curious, have you said anything to dealer? If so what did they have say?
  18. Replies
    37
    Views
    3,595

    the inner one has exhaust inside it and between...

    the inner one has exhaust inside it and between the inner and outer boot is cooling water. so if inner boot has damage it could be your leak.
  19. Replies
    37
    Views
    3,595

    your ingesting water from somewhere. if there was...

    your ingesting water from somewhere. if there was no water in hull to be ingested through the seals then it has to be a cross leak from cooling system. when you pulled it apart was the rubber boot on...
  20. Replies
    5
    Views
    897

    hard to read tag do to glare, but if I read...

    hard to read tag do to glare, but if I read correctly it says J700A that should be the 701 eng.
  21. Replies
    37
    Views
    3,595

    with the 93 VXR you'd have to dam near fill it to...

    with the 93 VXR you'd have to dam near fill it to the top of the hull to get it in the carb. the carb stands upright and is as high or higher than the head. my bet would be either intake manifold or...
  22. whatnissan, did you get manual from gmail...

    whatnissan,
    did you get manual from gmail sent to you?
Results 1 to 22 of 22