Search

Type: Posts; User: tman701

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    304

    Charger wheel upgrade alone isn't going to do...

    Charger wheel upgrade alone isn't going to do what you want. In simpler terms wheel upgrade will want more air, more fuel, will try to spin more RPM's by nature.
    The paddle wheel is gone and now the...
  2. Replies
    3
    Views
    212

    Lol, don't do it, don't touch the MAP sensor....

    Lol, don't do it, don't touch the MAP sensor. Drill/Tap the intake instead so that you don't run into issues. The MAP sensor is pretty sensitive and putting a T on that line seems to create issues.
  3. Those are for the timing chain guide. You will...

    Those are for the timing chain guide. You will need to use the new bolts when you replace the clutch due to clearance issues. Do them one at a time so that you don't mess with the timing chain.
  4. As long as it didn't overheat if you weren't...

    As long as it didn't overheat if you weren't using the hose to test this out then I highly doubt it, all you were seeing was probably the MAP sensor sending wonky signals to the ECU etc.. I don't...
  5. Yeah, that is the wrong way to do it...

    Yeah, that is the wrong way to do it unfortunately. It seem to work for some and not for others, but the general consensus is not to tap the MAF line because it messes with the ECU. Your symptoms are...
  6. Where are you tapping for your vacuum line out of...

    Where are you tapping for your vacuum line out of curiosity?
  7. Replies
    25
    Views
    4,176

    I have a 21 like you but with the wrong transom...

    I have a 21 like you but with the wrong transom plate and when I squeeze the go-fast lever, it takes off. Very little noticeable cavitation, its there but nothing like what you are describing. If i...
  8. Replies
    15
    Views
    586

    Ok, thanks for the info. Agree on that, will take...

    Ok, thanks for the info. Agree on that, will take a strong motor over those small annoyances.
  9. Replies
    15
    Views
    586

    Is the wiring on that particular plug...

    Is the wiring on that particular plug tight/stretched?
  10. It hits the RIDE motor in the back of the hull...

    It hits the RIDE motor in the back of the hull which is almost right up to the WaterBox. You can kind of see it in the pics.
  11. I can only tell you of my experience with my...

    I can only tell you of my experience with my Yamaha's.
    That link you posted was with cold starting and stalling, not stalling while out running your water craft, two very different things in my...
  12. Mine does it with the stock 21 grate. Not a big...

    Mine does it with the stock 21 grate. Not a big deal to be honest.
  13. Replies
    140
    Views
    32,426

    Sticky: No, the dealers aren't aware of what they are...

    No, the dealers aren't aware of what they are getting. Dealers usually put in their orders when new models come out and Yamaha fills those orders as they are produced. (more complicated than that but...
  14. Replies
    9
    Views
    585

    Check out this thread, its the intake grate...

    Check out this thread, its the intake grate design that is causing the vibrations. I felt it on smooth lake type water but not when riding in the choppier ocean waters.
    ...
  15. Replies
    4
    Views
    150

    Did you also change the oil filter? Sounds like...

    Did you also change the oil filter? Sounds like you did but just to make sure. Maybe the difference is due to installing a new oil filter with no oil in it? Not sure it would account for all of it...
  16. Replies
    18
    Views
    1,884

    I honestly don't think RiDE is used with the...

    I honestly don't think RiDE is used with the auto-trim feature, at least not that I have noticed on mine when I enable auto-trim.
  17. Replies
    74
    Views
    8,294

    Thanks for the update Jerry. Mine falls within...

    Thanks for the update Jerry. Mine falls within the WB range of Primary ID numbers.
  18. Replies
    15
    Views
    1,006

    So far I am the only SC ski in the group I ride...

    So far I am the only SC ski in the group I ride with. I have never ran out of fuel on any of our outings since I'm maintaining my pace with theirs. On the contrary, when we start to open it up, their...
  19. Cant wait, 2 awesome machines.

    Cant wait, 2 awesome machines.
  20. Replies
    74
    Views
    8,294

    They have always been good with me too. I haven't...

    They have always been good with me too. I haven't really had many interactions with them but when I have it has been stellar from both the dealer and Yamaha. Hoping this will go as smooth.
    The...
  21. Replies
    74
    Views
    8,294

    Therein lies the problem. How do I get my dealer...

    Therein lies the problem. How do I get my dealer to claim this to Yamaha as a warranty claim if at all? They will ask if the ski is not able to be ridden?

    I am calling them along with attempting...
  22. Replies
    74
    Views
    8,294

    Ok, did some digging in the OEM parts finder. If...

    Ok, did some digging in the OEM parts finder. If that is correct here is what I found because the part #'s didn't make sense, so I went as far back as 2018 looking for that part#. If the casting is...
  23. Replies
    74
    Views
    8,294

    I agree, I am going to start trying to contact...

    I agree, I am going to start trying to contact Yamaha directly to see what they have to say.
    Gerry, is this something you can also bring to the attention of any Yamaha folks?

    Can someone...
  24. Replies
    74
    Views
    8,294

    Thanks SHHR, Just checked and mine has 6CS1, not...

    Thanks SHHR,
    Just checked and mine has 6CS1, not good, not good at all. Need to start contacting Yamaha because if we paid for certain parts on my ski then that is what I expect it to have.
  25. Replies
    74
    Views
    8,294

    @shhr what is the build date of your GP? Mine was...

    @shhr what is the build date of your GP? Mine was built in Sept and delivered to me in Oct.
    Can we check it reliably without dismantling the pump?
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4