Search

Type: Posts; User: Mr. GP1800

Page 1 of 8 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    5
    Views
    60

    The nano material is kind of soft and not very...

    The nano material is kind of soft and not very dense. If you ever drill it you will see what I mean compared to the SMC of the older hulls. A hole saw cuts through it like butter.
  2. Replies
    5
    Views
    60

    I would look into coating that with something. I...

    I would look into coating that with something. I have some wear on the keel of mine but it’s not as bad as that. I have been looking at some of the airboat coatings
  3. Sticky: Only if you use too much grease. A few pumps is...

    Only if you use too much grease. A few pumps is all it takes
  4. Replies
    14
    Views
    673

    well I guess that solves that problem. No need...

    well I guess that solves that problem. No need to buy a different part.
  5. there’s still a grease fitting. It’s just on the...

    there’s still a grease fitting. It’s just on the housing and you have to reach in and find it.
  6. Replies
    14
    Views
    673

    if the part numbers on the rest of the pump...

    if the part numbers on the rest of the pump remained the same from the 2020 models then I would thing it’s compatible
  7. Replies
    14
    Views
    747

    I bet all it would take is some straight pipe and...

    I bet all it would take is some straight pipe and a 90 off the water tank. With some straight couplings.
  8. Replies
    14
    Views
    673

    2021 GP 1800 transom plate

    Does anyone know if the 2021 transom plate is available yet or when it will be available?

    Has anyone actually measured one to compare it to the 2020 and earlier version?

    Im thinking this...
  9. Replies
    19
    Views
    2,293

    This is what I bought ...

    This is what I bought

    http://greenhulk.net/forums/attachment.php?attachmentid=470544&stc=1
  10. I use a 1/4 hex drive impact driver to spin bolts...

    I use a 1/4 hex drive impact driver to spin bolts out after breaking them loose by hand.
  11. While the large Garmin screens are nice the 4...

    While the large Garmin screens are nice the 4 inch screen models work just as well and can be had for about 300 bucks. The other upside of this is that you can set up the sonar for depth readings...
  12. Why not switch to one of the echomap Garmin units...

    Why not switch to one of the echomap Garmin units and install it on your ski. There are so many more options available to these units and some are cheaper than the handheld versions.
  13. Replies
    14
    Views
    747

    I had thought of possibly wrapping the aluminum...

    I had thought of possibly wrapping the aluminum pipe for the rear exhaust kit to try and soften the exhaust tone some. That aluminum pipe is very resonant and probably adds to the noise factor. I...
  14. Replies
    4
    Views
    217

    Hi jay!!!!

    Hi jay!!!!
  15. Replies
    16
    Views
    542

    Jay is the man for sure!!!!

    Jay is the man for sure!!!!
  16. Replies
    16
    Views
    542

    https://www.millennium-tech.net/serviceInfo.php?id...

    https://www.millennium-tech.net/serviceInfo.php?id=15

    This is for a 4 stroke head. But a 2 stroke head should be easier and cheaper.
  17. Replies
    16
    Views
    542

    View Post

    Iím pretty sure millennium can fix that head. Did you tell them itís a single piece head for 3 cylinders? I think they weld the damage and then use a cnc to machine the damaged head exactly like...
  18. Use soapy water on the hull. Then you can slide...

    Use soapy water on the hull. Then you can slide the graphic around and position it exactly. Use an old credit card to squeegee the water out from under the decal. Let it sit a day to fully adhere.
  19. Replies
    14
    Views
    429

    This is exactly what I did. On one machine the...

    This is exactly what I did. On one machine the nipple on the jet pump nozzle split while tapping it. Its thin cast aluminum so its easy to break it. So I cut it off and I tapped the nozzle casting....
  20. Replies
    19
    Views
    2,293

    I’m working on this now. I have purchased an...

    I’m working on this now. I have purchased an analog to NMEA 2000 converter. I should be able to tap into analog sensors to display any data I want.

    So far my plan is for engine rpm, fuel level,...
  21. Replies
    10
    Views
    558

    With a catch can or breather mod any oil that...

    With a catch can or breather mod any oil that does go to the breather won't end up in your intercooler. When I had the breather hose connected to my Riva intake I had enough oil in the tube that it...
  22. Iseem to remember buying 91 octane fuel on the...

    Iseem to remember buying 91 octane fuel on the water there last summer when I was there
  23. Replies
    15
    Views
    1,148

    it can still spin only one way and be bad. It...

    it can still spin only one way and be bad. It may be slipping when trying to make boost. Definitely check all the hose connections if they are all good then I’d still suspect the clutch
  24. He’s on facebook. I think his name is Juan santos

    He’s on facebook. I think his name is Juan santos
  25. Replies
    3
    Views
    216

    I wouldn’t be surprised if they could be...

    I wouldn’t be surprised if they could be modified to fit.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4