Search

Type: Posts; User: BLASTER 1

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. I’ve used that hole on my FZ and GP. I used a...

    I’ve used that hole on my FZ and GP. I used a bulkhead fitting like this and 2 90* barbed fittings. Made some aluminum washers so the hex sides would not gouge into the nano, sealed with 5200. Works...
  2. Replies
    15
    Views
    1,148

    Check your hose from the charger to intercooler...

    Check your hose from the charger to intercooler and from intercooler to TB if one was loose and popped off you would be down on power big time. That’s best case scenario, if those 2 hoses are fine...
  3. Replies
    3
    Views
    335

    Anytime

    Anytime
  4. Replies
    3
    Views
    335

    Head Bolts- 40.6 ftlbs + 90*turn Lower Case- M-6...

    Head Bolts- 40.6 ftlbs + 90*turn
    Lower Case- M-6 7.4 ftlbs. M-10 22.1 + 90*
    Rod Bolts- 37.6 ftlbs + 90*
  5. Replies
    35
    Views
    4,167

    View Post

    Dam Dan, thatís faster then a SR-71 right now. Thatís flying
    What rpm are you turning. Sounds like you have everything sorted out and dialed in

    Congrats
  6. Replies
    6
    Views
    482

    Please do not connect to the map sensor, it...

    Please do not connect to the map sensor, it could/will mess with fueling. Tap into the intake manifold and run that line to the bov.
    Do a search on tapping into the manifold
    Its pretty easy to do
  7. Replies
    8
    Views
    464

    https://www.4-tecperformance.com/index.php?main_pa...

    https://www.4-tecperformance.com/index.php?main_page=product_info&products_id=5172

    Here you go! Another option is to look for a used motor on the GH classified section, my kid found one but he...
  8. Replies
    13
    Views
    548

    Ok, so nothing works getting the bolt out First...

    Ok, so nothing works getting the bolt out
    First you have to gain access to the bracket, so remove what you have to to gain access. From the rideplate side screw-in your good bolt Then from the...
  9. Replies
    13
    Views
    548

    I would try spraying it with blaster penetrating...

    I would try spraying it with blaster penetrating oil and tapping it with a hammer to try and break the bond of corrosion. Then try those vise grips again, if your able to remove that bolt make sure...
  10. Replies
    8
    Views
    464

    Do what Ben said, my kid and I went through this...

    Do what Ben said, my kid and I went through this same scenario a month ago but it was the #2.
    He bought a short block from Jerry, bought all the special tools and he’s up and running better than...
  11. That’s what I would try, as long as the plate...

    That’s what I would try, as long as the plate thickness doesn’t mess with any clearance issues. Clean up the mid wall as best you can use the bearing housing as a template and use 5200 to seal that...
  12. Replies
    3
    Views
    436

    Nice, If you change that stock impeller to the...

    Nice, If you change that stock impeller to the solas you should pick up a couple mph and some acceleration
  13. Replies
    18
    Views
    1,524

    What model and yr ski are you modding? I know...

    What model and yr ski are you modding?

    I know with my 17 GP I first did direct connect to both cold air intakes and my seat would shudder or almost flap like wings by my knees. It would also...
  14. Replies
    13
    Views
    848

    Yea I’m not familiar with deans tunes, what stage...

    Yea I’m not familiar with deans tunes, what stage is it and do you have all the supporting mods for it. If you do I would think you’d be in the upper 80’s for sure
  15. Replies
    13
    Views
    848

    Can you list every single thing that has been...

    Can you list every single thing that has been done to this ski? That way people can help you out more
  16. Replies
    4
    Views
    296

    Yes, you’ll be fine

    Yes, you’ll be fine
  17. Replies
    13
    Views
    848

    Something is not right here! There’s no way you...

    Something is not right here! There’s no way you can pickup 1000 rpm switching from a 13/20 to a 13/18. I can see a 200 to 300 max but not 1000

    Your speed speed at 8400 is about right but the...
  18. Replies
    7
    Views
    544

    I’m not sure what your top speed will be but I’m...

    I’m not sure what your top speed will be but I’m guessing at that rpm it would be at least 8-10 mph faster than stock. With that said I would highly consider the Riva intake grate! I do not trust...
  19. Replies
    13
    Views
    848

    ???????????? Whats your rpm at top speed with...

    ????????????
    Whats your rpm at top speed with the 2 props?
    Hows the acceleration compare between the 2?

    Answering the first question might determine if the prop needs a little tweak
  20. Replies
    18
    Views
    1,086

    Yea, I would use just regular rtv silicon. I...

    Yea, I would use just regular rtv silicon. I don’t use Anything on the vein side of the pump
  21. Replies
    18
    Views
    1,086

    Casting resin is good, that’s what I used

    Casting resin is good, that’s what I used
  22. Replies
    18
    Views
    1,086

    DanSvho, make sure u fill the voids in the...

    DanSvho, make sure u fill the voids in the transom with epoxy or resin before you reinstall. It makes for a much better seal
  23. Replies
    14
    Views
    703

    That’s the reason to use 5200, if it’s done right...

    That’s the reason to use 5200, if it’s done right your never going to have to do it again
  24. Was this issue ever solved? What was causing the...

    Was this issue ever solved?
    What was causing the problem
  25. Yes, if all the information is correct it should...

    Yes, if all the information is correct it should be a better clutch from 2020 on down
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4