Search

Page 1 of 6 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    15
    Views
    670

    You stated brand new OEM stator - Where did you...

    You stated brand new OEM stator - Where did you get it and are you sure it's OEM? There is an aftermarket Stator being sold by several retailers that have questionable quality records. If the prior...
  2. Replies
    5
    Views
    536

    140s is normal for the 780. Take a look at the...

    140s is normal for the 780. Take a look at the head gaskets... The 780 gaskets are doubled up with two small rivets holding them together. If it is a single gasket, it can bring the dome closer...
  3. Sticky: I know this is old, but for future readers, the...

    I know this is old, but for future readers, the high speed cap is simply pulled off with a pair of needle nose pliers.
  4. Replies
    42
    Views
    1,284

    Try running a ground from the battery direct to...

    Try running a ground from the battery direct to the ground terminal in the ebox. This will bypass the ground from the stator to the ebox which is buried in a wire harness and can be burnt.... I...
  5. OUCH!! :smt044

    OUCH!! :smt044
  6. May want to take a close look at the crank if...

    May want to take a close look at the crank if there was water in there..... Probably rust too.
  7. Replies
    7
    Views
    900

    Use a large adjustable wrench instead.....

    Use a large adjustable wrench instead.....
  8. Thread: Towing

    by BlueFishCrisis
    Replies
    1
    Views
    273

    The cooling water intake is what needs clamped,...

    The cooling water intake is what needs clamped, but only if towing at planing speeds. No need to clamp if towing at idle or no wake speeds. At planing speeds, water if forced into the pump tunnel...
  9. WTB Make sure the screen and orifice are clean. ...

    Make sure the screen and orifice are clean.

    http://www.greenhulk.net/forums/attachment.php?attachmentid=418786&stc=1
  10. WTB There are 3 connections to the exhaust pipe. ...

    There are 3 connections to the exhaust pipe. The large connection at the Front of the ski (when the pipe is installed), the small inlet at the top of the ski (with screen and orifice) and the small...
  11. Replies
    9
    Views
    1,324

    The seals can be replaced. ...

    The seals can be replaced.

    https://sites.google.com/site/polarispwcknowedge/Home/first-things-to-do/keeping-your-polaris-pwc-on-the-water/jet-pump
  12. Still sounds fuel related to me. I wouldn't go...

    Still sounds fuel related to me. I wouldn't go pulling the flywheel on a bad shear key just yet. IF it was sheared, it would not typically reach full RPM or wouldn't start at all.

    What type of...
  13. Replies
    2
    Views
    820

    http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=399495&stc=1
  14. Replies
    1
    Views
    657

    Don't worry about aftermarket steering.. Get a...

    Don't worry about aftermarket steering.. Get a finger throttle, extended pump, upgrade your fuel system, put in recommended plugs, and perform regular maintenance and you will have fun.....
  15. That is correct. It is a temp sensor.

    That is correct. It is a temp sensor.
  16. Replies
    10
    Views
    995

    The 780 motors do not run off of the battery so...

    The 780 motors do not run off of the battery so once it starts, it will run with the battery disconnected.

    The recommended maintenance that K447 listed is more mandatory than recommended, if you...
  17. Sticky: Whoever was leaking!!

    Ah... I see now. A new dock at the cottage? Don't recall that ski parking setup in prior years. Cool!

    So who gets the lifts?

    Cheers![/QUOTE] Whoever was leaking!!
  18. Sticky: -I broung 4 Fujis, my SLT 750/780 with Triple...

    -I broung 4 Fujis, my SLT 750/780 with Triple pipes, an SLX 780, an SLT 750, and an SLT 780. My ride plate bolts kept coming loose and letting water in the hull on the SLT 750/780 with triples, and...
  19. Welcome! Did you try disconnecting the rev...

    Welcome! Did you try disconnecting the rev limiter wire from the CDI? If you did, than it is possible that the stator is bad. Had a similar issue with an SL780. Everything checked out including...
  20. Replies
    4
    Views
    2,325

    If the wires to the stator were replaced, it is...

    If the wires to the stator were replaced, it is likely they were fried at some point by contacting the batter positive to a ground at some location. This causes the thin black ground from inside the...
  21. Replies
    6
    Views
    497

    Necessary? No, the motor will still spin the...

    Necessary? No, the motor will still spin the driveshaft which will turn the impeller and make the ski go. However, a bad alignment will cause premature wear on the splines where the drive shaft and...
  22. Replies
    32
    Views
    3,355

    1/4" rubber fuel hose

    We posted at exactly the same time… Trippy!!! Sounds like you have it sorted out now. Make sure you get that screwed into place and hopefully the threads on the inserts aren't buggered up. You...
  23. Replies
    32
    Views
    3,355

    I would put one on. Won't hurt.

    I would put one on. Won't hurt.
  24. Replies
    65
    Views
    3,695

    In addition, once you have removed the jet pump...

    In addition, once you have removed the jet pump to remove and inspect the bearing, you need to inspect the drive shaft surfaces where the bearing rides. If there are grooves worn into it you will...
  25. Sticky: I'm committed for 4, with payment by the 10th.

    I'm committed for 4, with payment by the 10th.
Results 1 to 25 of 134
Page 1 of 6 1 2 3 4