Search

Type: Posts; User: nmpeter

Page 1 of 8 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    2
    Views
    58

    has to be possible to remove, since water left in...

    has to be possible to remove, since water left in there during a winter would freeze and ccompromise it.

    doesn't appear to have any direct fasteners, so my guess is the front slips into a clip of...
  2. Replies
    12
    Views
    200

    I've suggested numerous time to forgot he primer...

    I've suggested numerous time to forgot he primer and use a small squeeze 2-3 oz bottle with some premix to get some fuel thru the holes drilled in the f/a cover to fire the engine. Primers, in my...
  3. Replies
    27
    Views
    4,091

    sorry to be repeating the sale old advice after 5...

    sorry to be repeating the sale old advice after 5 years, but any ski sunk in saltwater is going to require a complete go over of every single electric connector and bolt on the ski. any salt that was...
  4. Replies
    11
    Views
    182

    still 13% over book but far closer to making a...

    still 13% over book but far closer to making a deal

    lets see her
  5. Replies
    11
    Views
    182

    well 35K canada is way above book value, looks...

    well 35K canada is way above book value, looks nice and clean however, but if he's expecting above book value, he best have a file folder full of service receipts

    of course I'm sure that boat is a...
  6. Replies
    11
    Views
    182

    I'll politely disagree, simply due to my...

    I'll politely disagree, simply due to my experience on working on seadoo boats for several years

    I've seen plenty on n/a 4 techs make it to 800 hours+, _with_ regular maintenance. Our local rental...
  7. Replies
    11
    Views
    182

    seadoo boats are no longer serviced by dealers ...

    seadoo boats are no longer serviced by dealers

    outside of the engine, parts are all but impossible to find, need trim or seats?..good luck there

    450 hours means engine rebuilds are imminent.
    ...
  8. Replies
    7
    Views
    283

    get a pressure washer

    get a pressure washer
  9. I kinda have doubts. why not humor the old...

    I kinda have doubts.

    why not humor the old captain and swap them and dump a teaspoon of premix down the jugs to be sure?
  10. check to be sure you do not have the return line...

    check to be sure you do not have the return line and feed line switched

    and by the way, you did remember to turn on the fuel valve, right?
  11. I figure DFI is out of the PWC emm repair...

    I figure DFI is out of the PWC emm repair business for at least five years now, so it's entirely possible the emm suffered another age related failure. This emm operates under what I'd politely call...
  12. just so you know, those are " i don't really want...

    just so you know, those are " i don't really want this no-profit pain in the ass job" prices, followed by " if your dumb enough to pay me this much I'll do it, but don't expect it back for a couple...
  13. Replies
    32
    Views
    633

    I truly dislike having to repeat myself ...

    I truly dislike having to repeat myself

    but...

    this shows the housing assembly as well


    http://greenhulk.net/forums/showthread.php?t=230853
  14. Replies
    84,423
    Views
    6,113,641

    They should expect a cease and desist order early...

    They should expect a cease and desist order early next week. In one of his many TV interviews The gun toting attorney said he is a bit pissed about the unauthorized use of his image for commercial...
  15. Replies
    9
    Views
    174

    why not just send it back to leaders to get it...

    why not just send it back to leaders to get it flashed?

    might want to ask the guys at candoopro.com if they can provide some help/advice on this issue, but you really need to contact leaders about...
  16. a little fuel down there will confirm the engine,...

    a little fuel down there will confirm the engine, but from what you describe the carbs are plugged. wouldn't hurt to examine the condition of the rotary valve while the carbs are off, and replace if...
  17. rotary valve fault, assuming you have a good...

    rotary valve fault, assuming you have a good spark ( which you didn't actually mention)

    the only way to confirm the rv is to remove the rv cover.

    don't use ether. a teaspon of gas down the plug...
  18. Replies
    9
    Views
    229

    With obvious rat damage to the old post, you...

    With obvious rat damage to the old post, you opened the possibility that the issue here is chewed wiring

    ski history is important

    check to be sure the IAC is actually getting some voltage when...
  19. Replies
    4
    Views
    171

    followup tax has been assessed on this message,...

    followup tax has been assessed on this message, make sure to come back and let us all know what was really wrong....

    "or else"

    :-)
  20. Replies
    9
    Views
    229

    when the IAC valve is misbehaving the...

    when the IAC valve is misbehaving the transitional from idle to throttle plate controlled speeds will be too lean ( too much air ) and then a stall. You should hear the IAC cycle when the key is put...
  21. Replies
    4
    Views
    171

    yeah, find a new shop that isn't trying to make...

    yeah, find a new shop that isn't trying to make the rent. 120 is low, but serviceable if all four were at or close to that number

    btw the exhaust manifold and system is the only thing directly...
  22. you would think the folks making the billet nut...

    you would think the folks making the billet nut would make it eye-dentical to the factory part as far as nut size

    you would think.....

    they didn't

    after I form up whatever pvc tool I'm...
  23. Replies
    9
    Views
    229

    Welcome aboard GH change the plugs, its always...

    Welcome aboard GH

    change the plugs, its always the plugs.....

    yeah I know I know..the "look" fine...

    Now if its not the plugs, its going to turn out to be the idle air controller valve. Its...
  24. you can typically form the correct size for...

    you can typically form the correct size for things like this by using some 1 inch PVC and a little heat on the billet part to melt the plastic into the desired shape. You can try that if your...
  25. Replies
    4
    Views
    746

    The Green Hulk store carries it. Kawasaki...

    The Green Hulk store carries it.

    Kawasaki Candoo code reader
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4