Search

Type: Posts; User: Kinchyle

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    795

    Sure thing. XP how do you want me to paypal your...

    60 bucks?[/QUOTE]

    Sure thing. XP how do you want me to paypal your email address ?
    Psycho I'll buy yours for a rainy day if you want to part with them.
    M80's in the lake and flying over fish...
  2. Replies
    7
    Views
    795

    Hey there's more folks I remember! How come the...

    Hey there's more folks I remember! How come the new x's didn't take to them. Definitely greater tracking and speed. Just can't spin out as well. I'll contact Daniel unless you want me to buy yours...
  3. Replies
    7
    Views
    795

    Rideplate skegs, where did they go ?

    I had the rideplate skeg "glue-on" mod for the RXT. I lost one and can't seem to find them in the store.
    These gave me a mph and a whole lot more stability on the waves/wakes.

    Are these still...
  4. Replies
    5
    Views
    771

    Interesting connections, never thought about...

    Interesting connections, never thought about trying to relieve back pressure. I was thinking of more increasing flow on front side.

    3/4 pump in-hose to inline filter to y or t fitting. One side of...
  5. Replies
    5
    Views
    771

    Yes stock j pipe and external ic(cx racing on...

    Yes stock j pipe and external ic(cx racing on ebay) 12x12x4
  6. Replies
    5
    Views
    771

    RXT with X water routes, which method ?

    I'd like to switch my water routes to how the X is setup.
    I have a reduced tee (looks a little smaller than 1/2). I also have the green washer from the X setup.

    I'm on the fence of just using the...
  7. Replies
    1
    Views
    597

    Transom tranducer and spinning around

    Is there risk to breaking a rear/transom transducer if you are spinning out and hotdogging on a jetski.


    Also what's a good fish finder I was leaving toward this
    Lowrance elite 4 hdi gold ....
  8. Replaced front oil sensor and took the top off...

    Replaced front oil sensor and took the top off the tops valve next to the oil tube and shook it a little. I verified it clicked and made hum noise when I plug up the lanyard. Rode for a couple hours...
  9. Poll: Found x washer on replacement parts. If ic is in...

    Found x washer on replacement parts.
    If ic is in a downward angle (and as ski angles up)what is best route for water going in the front or back ?
  10. Replies
    29
    Views
    3,570

    Just make sure you haven't plugged the key in for...

    Sounds like a piece of cake. I read something about having to depressurize the fuel system first. Yes or no? How is the throttle cable removed? Guess I'll need to take a closer look at that as...
  11. Replies
    29
    Views
    3,570

    Don't forget to pressure test ic. Plug it to hose...

    Don't forget to pressure test ic. Plug it to hose and run water make sure no water. I replaced mine with cxracing ebay 12x4.5 3/4 water. It matched my other plumbing (siliconeintakes.com)
  12. I have 05 rxt. Will the analog dial work also? I...

    I have 05 rxt. Will the analog dial work also? I generally leave digital on rpm
  13. Hey psycho!!! Long time.. I checked the plugs...

    Hey psycho!!! Long time..

    I checked the plugs on the front of the engine and all the metal clips are facing engine or up. Was hoping it would just be flipping a plug to fix this 8-[

    The plug...
  14. Removed/installed Intake Manifold now P1202 error

    Pulled the intake manifold to clean it and now I get random P1202 error. I can be at WOT, cruising at 5000 rpm, spinning around. It happens at odd times... I pull the key, plug it back up and it runs...
  15. Poll: Based on the feedback I think I'm going to go...

    Based on the feedback I think I'm going to go with washer modification and T fitting from the X ski.
    Anyone know which T fitting I need....
  16. Poll: So you can run an intercooler with no water and...

    So you can run an intercooler with no water and nothing happen ??
    I believe the SC can push about 200 degrees air right ?
    What if you had the intercooler with no water for 20 minutes with SC...
  17. Poll: This is what I thought was the most efficient,...

    This is what I thought was the most efficient, however when my filter clogged up and I had a slight pinch in the opas hose inside the ski it ended up overheating my IC and blowing a core then the...
  18. Poll: Water routes with External IC, what is concensus

    I have an external intercooler.
    I have the capability of having 2 water lines (stock and one from pump) and I have a pisser on the side of the ski.

    I use to have split water ways one going to the...
  19. Replies
    29
    Views
    3,570

    My intercooler is external and goes right after...

    I'm a novice here so please help me out. How does a burst intercooler toast a supercharger? Isn't the intercooler inside the intake manifold and it receives the air that the supercharger puts out? ...
  20. Replies
    133
    Views
    39,731

    Wow never thought I'd see this post pop back up:)...

    Wow never thought I'd see this post pop back up:)

    PS
    My thermostat has been running strong for 5 years!!
  21. Replies
    5
    Views
    1,418

    Thanks! I used 40nm which is 29lb. I'm going to...

    Use this:

    http://www.greenhulk.net/forums/showthread.php?t=222891[/QUOTE]


    Thanks! I used 40nm which is 29lb.
    I'm going to switch to 33nm (24lb) next time!

    Was always worried my pump would...
  22. Replies
    2
    Views
    854

    My check engine is going off too how did you get...

    My check engine is going off too how did you get the code
  23. Replies
    29
    Views
    3,570

    I'm going through the same thing. Mine was hose...

    I'm going through the same thing. Mine was hose pinch on intercooler (seperate water lines).
    Intercooler got to hot water burst from core and toasted SC.

    I'm doing new X charger with injectors...
  24. Replies
    5
    Views
    1,418

    Pump housing screw torque ??

    Manual says 12 and 23... Seems light. I lost my torque wrench and had to get another one. I think I had it at 30 but am leaning toward 40.
    What do yall use as safe torque ? I'm in the low 70's on...
  25. Replies
    3
    Views
    509

    Thanks Chris!! I re-checked all the "similar"...

    Thanks Chris!! I re-checked all the "similar" connections.

    I spent about 6 hours in the 95 degree heat today putting the seadoo back together and had the 2 big plugs on the top of the manifold...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4