Search

Which is faster? Nothing can catch this!!! No SeaDoo, No Yamaha!
Look how the tech has changed.

And what year 800SXR is it? the made them for many years.The 800 stock is a fast machine. For a first time standup its a lot of performance. That modified machine, well, i would think for beginner,...

Probably a post and ghost! Sadly.

Maybe the intake manifold cracked if it backfired. May have split it along the seam.

Just to clear some things up about how the bellows and carbon seal work.
#1, a soft Bellows will not cause the ski to sink, Heat fron running the engine onland will not hurt the bellows (unless it's...

Lost me with the line "With Guidance from Our Lord, " unless your refering to Jerry, owner of this site!

Are you saying you hear voices? And it told you how to prevent water in a gas tank?
...

You can still use that head, its just cooling passage to cooling passage. The integrity of the combustion part is not affected. No issue.

You will get conflicting reports because these are high strung machines (All high output skis, not just seadoo)
Things can break, even if you maintain it and take care of it. You reduce the chances...

Are you sure you didn't remove the spark plugs and valve cover and spark plug tubes, then crank the engine over? Maybe to do a compression check? The keeper fell down the spark plug hole and it hit ...

4 gallons! Ah thats way more than you need, a gallon at most.
To prevent carbon seal melt down, try it this way.
Do not start the engine, pour in 1/4 a gallon though the flush port. Start engine...

ARP all the way, and mine came with installation and torque instructions. Reusable, stronger, consistant. No "measuring", just piece of mind its right every time.

So you keep replacing the rings without finding the cause of the problem. Sorry, if I had a ski that needed 6 rings in maybe 24 months of use I would suspect something else is wrong.

Yes, arrows point in the direction of flow, so from pump to engine
Run 50:1 premix until the lines fill with oil .
If the line from the tank to the pump has air in it, open the bleed screw on the...

There is no need to redesign it, a properly installed and aligned seal will last over 200 hrs and many years.
I replaced mine at 150 hrs and 14 years and it was not leaking and only worn down 1/8 of...

It idles at 2800 RPM? After a hard turn?
Does it idle at 1800 at startup?
Have you checked your throttle cable for sticking? There should be just a little bit of slack in the cable when the...

Nope, hundreds of hrs on our trixx, lots of hard jumping and landing. No wear ring damage from that.
Broke one in its life and it was from sucking up a rock.
Debris in the pump is the only thing...

Did you just try flushing the open loop part before you send it to the dealer? Maybe you sucked up some weeds or sand. Flushing it reverses the flow and may solve your issue. There is a "strainer"...

It should help some, but the biggest loads are often side loads when turning towing a tube.
Good work though!

You want a rope long enough to get the ski being towed as much out of the towing ski's jet blast, otherwise your just adding to the load.
If it can tow a tube, towing any ski would be no problem as...

Simple, check oil level, if its good. Charge up the battery ( not in ski)
Check all clamps and hoses.

First start after a superchanged ski has been sitting a long time, is Hold the Throttle at...

My money is on another rock in the pump. I always pull the pumps for rock ingestions as ther can be one behind the blades jamed to the stator.
Also allows for better inspection for damage and a...

I see your problem, engine fell out and is not in a 300RXPX anymore. :)

To check the oil pressure regulator the engine has to be pulled. I would first remove the oil filter cap and look at the filter. Has it collasped?
Then i would connect a gauge to the port at the...

8 Million? Price came down! :)

Banning guns won't do much, a criminal, or nutjob wants a gun, they will get it.

Now on the lighter side:

Canada criminal with a gun.

Police: Sorry to bother you sir, but can you please...