Search

Type: Posts; User: K447

Page 1 of 8 1 2 3 4

Search: Search took 0.35 seconds.

  1. Replies
    27
    Views
    2,805

    Drive Control apparently does affect top speed ...

    Drive Control apparently does affect top speed

    http://greenhulk.net/forums/showthread.php?t=293890&p=3136162&viewfull=1#post3136162

    How to disable Drive Control for maximum performance, Yamaha...
  2. Thread: Cone Grease

    by K447
    Replies
    2
    Views
    111

    Year and model?

    Year and model?
  3. Replies
    1
    Views
    82

    Welcome. If you have not found it already,...

    Welcome.

    If you have not found it already, save this link and then read up on the Ficht fuel injection and the MSX 140 related material
    http://polarispwcknowledge.shorturl.com/first-things-to-do...
  4. I removed two more Yamaha OEM impellers just in...

    I removed two more Yamaha OEM impellers just in the last week.

    Same on-the-ground method worked each time.
    I do lay a flat scrap of plywood under the pump duct to protect the casting surface....
  5. First he needs the spline tool, which he does not...

    First he needs the spline tool, which he does not yet have.

    Regarding welding the spline tool onto a trailer hitch drawbar, it seems more effort than simply using a breaker bar and deep socket on...
  6. Cold weather riding gear = season extender...

    Cold weather riding gear = season extender
    http://greenhulk.net/forums/showthread.php?t=291819&p=3119519&viewfull=1#post3119519
    ...
  7. Thread: Trailer size

    by K447
    Replies
    18
    Views
    808

    Tip: I prefer to set the Triton winch post angle...

    Tip: I prefer to set the Triton winch post angle to be vertical, or near vertical. And the single bolt that clamps the top of the angle support to the vertical post needs to be properly tight.

    On...
  8. Thread: Trailer size

    by K447
    Replies
    18
    Views
    808

    Triton used to include the guide roller as...

    Triton used to include the guide roller as standard on the previous version of the winch stand. The Triton supplied guide roller was rather small diameter and did not roll very well when there was...
  9. Replies
    4
    Views
    73

    Well, I do not have a red engine Polaris flywheel...

    Well, I do not have a red engine Polaris flywheel nut at hand to measure.

    Perhaps someone reading this thread will.
  10. Replies
    7
    Views
    328

    The tune should specify which sensor range the...

    The tune should specify which sensor range the tune requires.
  11. Were these holes present when you had the pump...

    Were these holes present when you had the pump seal kit filling the intake grate casting voids?
  12. Replies
    7
    Views
    383

    I use the CANDooPro diagnostic system. There is a...

    I use the CANDooPro diagnostic system. There is a hardware adapter box and cables to connect to the ECU.

    Depending on the model and year the Yamaha ECU connector is different, so make sure you...
  13. Are there also holes into the water flow zone...

    Are there also holes into the water flow zone above, through the angled ramp?
  14. Replies
    4
    Views
    73

    You have the flywheel nut? Take the nut to a...

    You have the flywheel nut?

    Take the nut to a machine shop, they should be able to confirm the thread size and pitch, and whether it is metric or inch standard.
  15. Replies
    7
    Views
    383

    What changed when the new spark plugs were...

    What changed when the new spark plugs were installed?
  16. Replies
    9
    Views
    459

    Your watercraft are ten+ years old. I think that...

    Your watercraft are ten+ years old. I think that era of Seadoo supercharger required periodic rebuild every so many running hours or two years, whichever comes first.
    You may need to be more...
  17. You can cross check factory part numbers on the...

    You can cross check factory part numbers on the various model years using the Polaris Industries parts diagram web site. If the part number is the same then the part did not change between those...
  18. Thread: Is it too late???

    by K447
    Replies
    18
    Views
    947

    What year and model? How many running hours? ...

    What year and model?
    How many running hours?

    How long has the water been inside the engine?

    How long was the ski underwater?

    Have you (or the dealer) opened and drained all the water from...
  19. You caught me! I made an error. :facepalm: ...

    You caught me!
    I made an error. :facepalm:


    Fixed it.
  20. Replies
    4
    Views
    153

    Why are you going to use an impeller from a...

    Why are you going to use an impeller from a supercharged model?
  21. What year is your SL650? Why do you want to...

    What year is your SL650?

    Why do you want to run the engine using oil pre-mixed into the fuel?

    1992 and 1993 Fuji engines have a bunch of additional cooling hoses down low around the engine,...
  22. My error was simply not actually reading the...

    My error was simply not actually reading the entire model name on the ski before starting the work. It says SHO right there after the FX, but I merely glanced at the SHO label without actually...
  23. Click on My Profile, top right of GH web site....

    Click on My Profile, top right of GH web site. Add your location info.

    There are GH members in the Milwaukee area with the spline holding tool. Perhaps one will see your post
  24. Using a vice may not be sufficient. Huge torque...

    Using a vice may not be sufficient. Huge torque may be required to crack the OEM impeller loose.

    http://greenhulk.net/forums/attachment.php?attachmentid=421345&d=1505349619
  25. Have you removed the stock OEM Yamaha SVHO...

    Have you removed the stock OEM Yamaha SVHO impeller yet?

    This is the Ďkit of toolsí I use for jet pump and impeller removal and installation.
    ...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4