Search

Type: Posts; User: CDW78

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Awesome! I'd like 4 please! 1 for each side of...

    Awesome! I'd like 4 please! 1 for each side of course ����
  2. Replies
    21
    Views
    1,324

    FS - Parts I've already sold the complete pumps.

    I've already sold the complete pumps.
  3. Replies
    1
    Views
    431

    Have the carbs ever been rebuilt ? If not, that's...

    Have the carbs ever been rebuilt ? If not, that's a good thing to do. Use Mikuni parts only. I'd stay off it until you're able to rebuild. I'd check all your connections to the fuel sending / sensor...
  4. You always start the engine THEN the water....

    You always start the engine THEN the water. Always cut water off then cut the engine off. If you've ran water into it without it running, you need to dry run it to make sure there's no water in it.
  5. FA's - Flame Arrestors are Air filters / box

    FA's - Flame Arrestors are Air filters / box
  6. Have you checked the tank itself ? Likely not the...

    Have you checked the tank itself ? Likely not the problem, but seems if you've checked everything else. Can you see any oil leaks with it running ? I'd swap out all the lines from the pump to the...
  7. Replies
    18
    Views
    856

    I do believe the water temperature sensor plug...

    I do believe the water temperature sensor plug being broken would stop it from firing all together. The plug goes into another plug connector on the side of the CDI unit. which should be right above...
  8. If you remove the pump and go to premix, no you...

    If you remove the pump and go to premix, no you don't have to change anything with the carbs. a lot of people prefer the premixed simply for the peace of mind and safety. You can keep the oil...
  9. Replies
    13
    Views
    1,133

    Hopefully this will be of some help, just my...

    Hopefully this will be of some help, just my thoughts, but maybe someone else will chime in soon!

    An SBT top end with sleeves would work, most don't prefer SBT or sleeves for that matter, depends...
  10. Replies
    1
    Views
    605

    IF you're sure everything is disconnected and all...

    IF you're sure everything is disconnected and all the bolts removed, it could be the sealant around each part that connects to another part of the pump. I know I had a heck of a time pulling mine out...
  11. Replies
    5
    Views
    384

    It is the ring your impeller spins in / Around...

    It is the ring your impeller spins in / Around the impeller, should be stainless unless of course its been changed to the plastic.
  12. Thread: Failing CDI

    by CDW78
    Replies
    6
    Views
    3,965

    A service manual for the skis listed on boats.net...

    A service manual for the skis listed on boats.net should work. All the same CDI. I assume like the rest, trouble shooting procedures are in it. Boats. net says the CDI fits the following models.
    ...
  13. Replies
    2
    Views
    1,416

    http://www.greenhulk.net/forums/showthread.php?t=6...

    http://www.greenhulk.net/forums/showthread.php?t=66055

    This thread may be of some help, WFO's post # 5 particularly
  14. Replies
    2
    Views
    335

    Some people don't during rebuilding. If you do...

    Some people don't during rebuilding. If you do take them out to replace the O rings on the needles, write down how many turns they were out / in. What kind of boat is it ? Your mods also can change...
  15. Thread: Gp1200r problems

    by CDW78
    Replies
    6
    Views
    537

    Are you saying you leak tested the carbs or the...

    Are you saying you leak tested the carbs or the engine after rebuilding ?
  16. Replies
    6
    Views
    528

    Maybe not the best option, but try vice grips...

    Maybe not the best option, but try vice grips around the head of the screw. Likely have to replace it for sure after that.
  17. Replies
    3
    Views
    3,172

    Premix would eliminate a lot of the oil line...

    Premix would eliminate a lot of the oil line issues and give you a huge piece of mind. Not too bad to do quickly if using a mixer like Ratio Rite or similar. Some people prefer the pump, def keep...
  18. Replies
    1
    Views
    454

    WTB - Parts Solas impelle billet seal / nose cone

    Anyone have it ?

    I had to destroy the blue one to get it off.


    For Solas 13/19 Concord / 2k gp1200r
  19. Maybe I had pulled some of the wires in the...

    Maybe I had pulled some of the wires in the front, I dont know, but disconnecting and reconnecting all the wires under the hood solved the problem.
  20. Hmmm. I know when I was over on the side messing...

    Hmmm. I know when I was over on the side messing with the chip & harnesses it did actually click over, but not 100% sure which one cause it to work.
    Would either the cat chip or temp sensor cause...
  21. Great, that answers that part of the problem! I...

    Great, that answers that part of the problem! I found the sticky on the DIY chip. From my understanding it's just the resistor. So could you just cut off the harness and solder it directly to the...
  22. Ok, so I checked the cat temp chip, I hit the...

    Ok, so I checked the cat temp chip, I hit the start button, attempted to turn over. Would a lose connection or bad chip cause it to act like this ? If so, anyone got any, read possible to make one ?
  23. Gp1200r everything checks good, but wont turn over

    Just got the engine and all reinstalled yesterday. I turned over a couple times and all was well. Was about to check check compression and now it won't do anything. Meter is working and so is that...
  24. Replies
    12
    Views
    1,995

    Got it installed with out issues! Thanks again,...

    Got it installed with out issues!
    Thanks again, def a hundred times easier, with all attached and hoist!!!
  25. Replies
    12
    Views
    1,995

    Thanks for a quick reply.... Def will make my...

    Thanks for a quick reply.... Def will make my life a little easier!!
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4