Search

Type: Posts; User: canuck

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    364
    Views
    59,496

    Winter project is a restoration on this, 1983...

    Winter project is a restoration on this, 1983 Yamaha RZ350K. It's now stripped to the bare frame which is getting sand blasted and powder coated the original factory red.
    ...
  2. Replies
    364
    Views
    59,496

    This thread has been quiet for too long. Picked...

    This thread has been quiet for too long. Picked this up a few months ago.
  3. Replies
    125
    Views
    21,984

    Heated grips and handlebar wind deflectors are...

    Heated grips and handlebar wind deflectors are listed as accessories for the P-X and T-X not sure about other models. I think I'll be keeping my 2015 RXT-X for at least another year.
  4. Replies
    37
    Views
    2,768

    Wow. The more I keep reading about the...

    Wow.

    The more I keep reading about the issues with quality control, gas in oil and the new finish makes me want to keep my 2015 for a few more years. I realize that all you read about are the...
  5. Replies
    5
    Views
    365

    Replace the flywheel bolts it's easy with the...

    Replace the flywheel bolts it's easy with the motor out.
  6. Replies
    4
    Views
    218

    I used ARP head studs on an previous 04 RXP build...

    I used ARP head studs on an previous 04 RXP build and the valve cover needed a little material removed in one spot so the valve cover gasket would fully seat. The ARP stud and nut sits a little...
  7. I think re using bolts needs a common sense...

    I think re using bolts needs a common sense approach, torque to yield bolts such as flywheel, rocker shaft, head bolts etc absolutely these need to be replaced. iBR assembly bolts, engine mount...
  8. Those look like ceramics, rebuild it with an oem...

    Those look like ceramics, rebuild it with an oem rebuild kit. I have seen those so called chips on lots of impellers so no need to replace, it's not actually a chip it's machined for a reason...
  9. I might try it in the hull on the earlier RXPs...

    I might try it in the hull on the earlier RXPs with the removable rear cowl any other model pull the engine.
  10. Replies
    15
    Views
    1,371

    I would not bother with just bearings if you're...

    I would not bother with just bearings if you're going as far as removing the supercharger and disassembling to do bearings you might as well do the full rebuild kit for a few dollars more.
  11. Carbon ring probably overheated and is now...

    Carbon ring probably overheated and is now damaged this needs to be checked before the next ride or it could take on water and sink the ski.
  12. I was thinking the same thing will this fit the...

    I was thinking the same thing will this fit the older S3 hull without too much modification ? I would guess the engine needs to be removed to get the tank into the hull the hole for the front...
  13. Replies
    7
    Views
    3,072

    Looks good. I bought the WCA-1500-56...

    Looks good.

    I bought the WCA-1500-56 watercraft trailer a few years ago for the same reason the bigger skis fit much better. Spare tire, Boat Buckles and proper safety chains are the only...
  14. Replies
    12
    Views
    817

    Same here bent the arm and now the gauge reads...

    Same here bent the arm and now the gauge reads closer to what's in the tank and stops the annoying low fuel alarm when you actually have over 1/4 tank left.
  15. Replies
    9
    Views
    843

    Can you mount a RAM ball somewhere on the...

    Can you mount a RAM ball somewhere on the steering cover ? This is what I did on my RXT-X which is a little easier due to the exposed hardware.

    I have a BRP glove box cover for your model that...
  16. Replies
    59
    Views
    4,184

    This video around the 1 minute mark shows the...

    This video around the 1 minute mark shows the pump cone being removed make sure the bearing cavity shows no signs of water intrusion or the pump bearing will not last long. If the pump bearing...
  17. Replies
    59
    Views
    4,184

    116KW = 155HP the pics are not the best, I don't...

    116KW = 155HP the pics are not the best, I don't see a supercharger so I would guess these are the 155HP non supercharged models. Clean them up, change the fluids and spark plugs check the pump for...
  18. Replies
    59
    Views
    4,184

    Here's where to get the 2004 shop manual. ...

    Here's where to get the 2004 shop manual.

    http://seadoomanuals.net/manuals/2004-seadoo-shop-manual.php

    Post a pic so we can help with what models you have.
  19. Replies
    3
    Views
    543

    What are you wanting that the stock bars and...

    What are you wanting that the stock bars and steering don't do ?
  20. Replies
    21
    Views
    2,279

    This is where you go for supercharger rebuilds: ...

    This is where you go for supercharger rebuilds: http://greenhulk.net/forums/showthread.php?t=146938
  21. Replies
    21
    Views
    2,279

    Here's part one of a video series we did on an...

    Here's part one of a video series we did on an engine rebuild after a supercharger failure.


    https://youtu.be/c-2LdY-hxmA
  22. Replies
    6
    Views
    542

    I would rebuild it with an oem kit. A 2008 with...

    I would rebuild it with an oem kit. A 2008 with unknown rebuild history is definitely due and it's a lot cheaper than fixing the damage if it does grenade.
  23. Get a multi meter and measure the voltage at the...

    Get a multi meter and measure the voltage at the battery terminals before you start the machine then measure again when it's running. A fully charged battery with no load should be 12 to 13V when...
  24. What's the battery voltage when the ski is...

    What's the battery voltage when the ski is running ?

    Have you checked the alternator connector near the throttle body these like to overheat.
  25. Replies
    12
    Views
    797

    I think it was just under 8300rpm it's been a...

    I think it was just under 8300rpm it's been a while since I have focused on speed runs. My speed numbers are from a Garmin GPS not the dash display which is optimistic by a few mph.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4