Search

Type: Posts; User: 32DegH2O

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    145

    WTB Ended up having to buy a new one.

    Ended up having to buy a new one.
  2. Replies
    19
    Views
    2,512

    FS Lowered some more prices

    Lowered some more prices
  3. Replies
    6
    Views
    214

    A very rich condition can cause bogging...

    A very rich condition can cause bogging (extremely rare to happen) as your jets would have to be much bigger than stock to do that. Since you are using the correct jets, it's not a rich issue. Have...
  4. Replies
    10
    Views
    478

    When I was referring to a detonation issue, I...

    When I was referring to a detonation issue, I meant in like the timing/electrical...not a carb issue. Unless you are running a really wrong octane level for your setup...the gas is not causing the...
  5. Replies
    19
    Views
    2,512

    FS TTT

    TTT
  6. Replies
    10
    Views
    478

    The tops of the pistons look like a detonation...

    The tops of the pistons look like a detonation issue is going on. Are the tops rough feeling and pitted?...it looks like they are.
  7. Yes the 707 is good for this ski....the 202 was...

    Yes the 707 is good for this ski....the 202 was the original predecessor to the 707 which Polaris went to with the MSX models
  8. Replies
    1
    Views
    145

    WTB 3 or 4 Place trailer in Minnesota Area

    Hi...looking to buy a good used or new 4 place watercraft trailer in the Minnesota area.
  9. Replies
    3
    Views
    129

    What he said :smt116

    What he said :smt116
  10. The numbers are under the head attachment ring so...

    The numbers are under the head attachment ring so unfortunately you have to remove the head bolts to see them.
  11. .

    .
  12. After sitting that long, did you replace the...

    After sitting that long, did you replace the front and back crank seals to the engine case? If not, they are going to be shot and leak air...which most likely is your lean cause. The seals need...
  13. Replies
    19
    Views
    2,512

    FS Added more items and lowered some prices.

    Added more items and lowered some prices.
  14. I vote detonation issue...unfortunately this...

    I vote detonation issue...unfortunately this could be due to a number of things. Even with junk aftermarket carb kits, it wouldn't get that bad that quick unless something was really done wrong...and...
  15. Replies
    3
    Views
    222

    Another thing to check is to make sure none of...

    Another thing to check is to make sure none of the gas lines have to tight of a curve/turn to them, especially near the water separator area where it's a tight space. The negative pressure in the...
  16. Replies
    14
    Views
    350

    If I missed it in a post somewhere...

    If I missed it in a post somewhere above...sorry...but do you recall the jet sizes that are in the carbs?
  17. Replies
    4
    Views
    132

    Personally I would not mix them at all. I would...

    Personally I would not mix them at all. I would get the one oil out of the tank and oil lines then put in the other stuff...but that's just me.
  18. Replies
    14
    Views
    350

    I Agree...also make sure your seal on the water...

    I Agree...also make sure your seal on the water separator is good and the ring nut is good and snug. Since you will have the carbs off to clean, make sure to check the pulse side as well to make sure...
  19. Replies
    14
    Views
    269

    You only need the lever part...it will fit on the...

    You only need the lever part...it will fit on the stock split block.
  20. Replies
    14
    Views
    350

    ok...so it's still stock stuff...so chances are...

    ok...so it's still stock stuff...so chances are better things should be ok...however, these machines are getting old and electronics do what they do. I suppose a CDI could go off course on it's...
  21. Replies
    1
    Views
    124

    WTB - Parts It shows you can still order them here:...

    It shows you can still order them here: https://www.partzilla.com/catalog/polaris/watercraft/2004/msx-140-w045303ca-ia/steering
  22. Replies
    14
    Views
    269

    It shows you can still order them here:...

    It shows you can still order them here: https://www.partzilla.com/catalog/polaris/watercraft/2004/msx-140-w045303ca-ia/steering
  23. Replies
    19
    Views
    2,512

    FS Due to no interest locally or otherwise in the...

    Due to no interest locally or otherwise in the empty hull, I will be removing all the remaining desirable parts and adding them to the used parts list within the next week.
  24. Replies
    14
    Views
    350

    Since it was a rebuild, have you verified the...

    Since it was a rebuild, have you verified the flywheel/timing is correct? Does the CDI appear to be stock?
  25. Replies
    14
    Views
    269

    You need to get the MSX/Octane finger...

    You need to get the MSX/Octane finger throttle...mounts right on...you do need to remove some of the handle bar padding (on a slt/sltx models) due to the the cable going to the front side. I've done...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4