Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    10
    Views
    1,168

    Cool build, how did the hull feel at 73? Sean

    Cool build, how did the hull feel at 73?

    Sean
  2. Replies
    23
    Views
    499

    Very clean install. Did you ground the wire to...

    Very clean install. Did you ground the wire to the gauge or to the ecu? I assume since the wire runs direct to the ecu you would drop the wire from the ecu to ground but lets confirm it.

    Sean
  3. Replies
    23
    Views
    499

    Which side did you ground? That is probably an...

    Which side did you ground? That is probably an obvious answer but I want to confirm since I have never messed with it.

    On another note, I can flash the ecu to a pre slo mode ecu if you want to...
  4. Replies
    23
    Views
    499

    Yeah the fuel level is tricky. I cut the tank on...

    Yeah the fuel level is tricky. I cut the tank on my nasty ski but I have been looking at older yamaha sending units that may work in the stock location.

    Kawasaki really likes non-linear sensor...
  5. Replies
    27
    Views
    4,745

    Its hitting on the pil pan? Sean

    Its hitting on the pil pan?

    Sean
  6. Not sure who told you that. The bottom end of the...

    Not sure who told you that. The bottom end of the 260 is good for 400+ hp on stockrods and crank. Change the cams, valves, and pistons, add boost and run race fuel and you ahould be set.

    The old...
  7. Replies
    23
    Views
    499

    Ip66 not rated for submersion but rated for water...

    Ip66 not rated for submersion but rated for water jets. The buttons were the leak path I was worried about but they seem to have good quality seals. The weak point seems to be where the wiring goes...
  8. Replies
    23
    Views
    499

    More Sean

    More

    Sean
  9. Replies
    23
    Views
    499

    This thing is actually pretty cool. Its on the...

    This thing is actually pretty cool. Its on the small side but it seems to be pretty well made. Size wise it should fit the stock opening pretty well with an adapter plate.

    Temp sensor looks to be...
  10. Replies
    65
    Views
    1,618

    Interesting part, was able to pull some...

    Interesting part, was able to pull some measurements off it but I will not be using it for the final install.

    Its glass fiber reinforced nylon which is a reasonable choice for the application...
  11. I see you must have come from yamaha land lol ...

    I see you must have come from yamaha land lol

    Sean
  12. Set the timing by the manual and its not a...

    Set the timing by the manual and its not a concern. Even if you are off by a tooth it wont contact.

    Sean
  13. The one with the a at the end of the number in...

    The one with the a at the end of the number in the diagram is the crank rotor. Try the other cam rotor/nub and see if it works. Was the engine running before it fell off the trailer?

    Sean
  14. Damn, I knew the gear was different but noticed...

    Damn, I knew the gear was different but noticed it was called a double row gear so I thought the pitch might be the same. Oh well.

    Thanks,

    Sean
  15. 300 supercharger on older 255 260hp engine conversion questions

    I currently have my 2008 215 and 255 engines out of their old hulls and am working on getting them up to spec before stuffing them into my STX hulls.

    I have to pull the pto cover off to swap the...
  16. Yep, sorry for being vauge. The cam trigger needs...

    Yep, sorry for being vauge. The cam trigger needs to match what the ecu expects.

    Sean
  17. If the engine is an 05 and the ecu is an 05 the...

    If the engine is an 05 and the ecu is an 05 the nub needs to be a 2005 nub.

    You have to match the ecu to the timing nub.

    Find out what engine you actually have and we can go from there.

    Sean
  18. Replies
    65
    Views
    1,618

    "Lower sodium" gtx 215 Sean 454931454932

    "Lower sodium" gtx 215

    Sean

    454931454932
  19. Replies
    65
    Views
    1,618

    Mmmmmm salty.... This is the x motor, the...

    Mmmmmm salty....

    This is the x motor, the rear left side motor mount was separated and fell apart when I pulled the motor up.

    Sean

    454918454919
  20. Im actually considering the same move. I am...

    Im actually considering the same move. I am curious what goes into doing the swap over and what dictates if you can or not.

    Sean
  21. Replies
    48
    Views
    2,241

    I stand corrected, my bad Waz. Looking back at...

    I stand corrected, my bad Waz.

    Looking back at the kawasaki website I can't find where it was at claiming to be a new hull. I think I mixed up the pages.

    The kawasaki brochure specifically...
  22. Replies
    36
    Views
    1,028

    Oooh got it. I thought you meant at the top of...

    Oooh got it. I thought you meant at the top of the can where it exits.

    Just get a new aftermarket pump: walbro, aem, aeromotive, desno whoever.

    Sean
  23. Replies
    23
    Views
    499

    On a 12f or 15f pre 2005 there is no slo mode,...

    On a 12f or 15f pre 2005 there is no slo mode, you can swap ecus back and forth to run without it but it requires swapping the tune or physical computer. I can reflash the ecus to not use it but only...
  24. Replies
    48
    Views
    2,241

    I consider rods and cranks interals lol The...

    I consider rods and cranks interals lol

    The riva vortech kits used stock 10.6:1 compression forged mtc pistons but stuck a spacer under the cylinders which is odd to me. They also ran on ms109. ...
  25. Replies
    48
    Views
    2,241

    Supposedly its not. Sean

    Supposedly its not.

    Sean
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4