Search

Type: Posts; User: king

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    45
    Views
    2,232

    Thanks for all who help me. Finally the end of...

    Thanks for all who help me. Finally the end of story :)
  2. Replies
    45
    Views
    2,232

    Hello I reset the timing for 3rd time then it...

    Hello

    I reset the timing for 3rd time then it start without hold the throttle and t run really smooth but I have question about the rpm, It should be stable on 1300 right ?
    Because mine rpm...
  3. Replies
    45
    Views
    2,232

    Yes, and I get same problem on the old timing...

    Yes, and I get same problem on the old timing (before reset)
  4. Replies
    45
    Views
    2,232

    I think the problem is from tps or iac so,today I...

    I think the problem is from tps or iac so,today I check the tps and it work well also, for iac is same.

    Anyone now how can I solve this problem?
  5. Replies
    45
    Views
    2,232

    I run it now it work just few second then it...

    I run it now it work just few second then it shutoff directly as you hold the throttle it work but the rpm is not stable and when remove my finger from throttle it will shutoff.
  6. Replies
    45
    Views
    2,232

    What I do is center punched without milled it...

    What I do is center punched without milled it flat so, when I drill it become one side very near to thread and other side little far from the thread then I use E-Z Out but when I tight it and turn it...
  7. Replies
    45
    Views
    2,232

    Hello everybody today, I try to make tdc by using...

    Hello everybody today, I try to make tdc by using the TDC gauge but the problem it is very hard to know if the mark on camshaft is aligned with the cylinder head.I adjust them but I am not pretty...
  8. Replies
    45
    Views
    2,232

    Hi, Because the collage closed now...

    Hi,

    Because the collage closed now <<<COVID-19. I return to work on my jet ski I receive the tdc gauge but the problem is the rod on the indicator is too short and now I try to make 120mm length...
  9. Replies
    45
    Views
    2,232

    I don't do anything because my collage holiday is...

    I don't do anything because my collage holiday is end so, I will come back and work on it next holiday.

    thank you Scottkrissinger for your interest
  10. Replies
    45
    Views
    2,232

    Ok, I will try to re-timing but, I need to use...

    Ok, I will try to re-timing but, I need to use TDC gauge because it is in the hull right? and after that I will upload the photo of it.

    Thank you Scottkrissinger
  11. Replies
    45
    Views
    2,232

    Yes, I count them it is 31 pins but the chain at...

    Yes, I count them it is 31 pins but the chain at exhaust cam always slack not go inside spoket and I don't no why

    thank you
  12. Replies
    45
    Views
    2,232

    Yes, the chain is slack always in exhaust cam...

    Yes, the chain is slack always in exhaust cam side I try to pull it then put the rest of chain on the intake cam but after I install the tensionor it jump again and become like the picture I don't...
  13. Replies
    45
    Views
    2,232

    I think yes, but can you see if it is right or...

    I think yes, but can you see if it is right or not ? and this is a photo of the timing I made before install the engine

    http://greenhulk.net/forums/attachment.php?attachmentid=457307&stc=1
    ...
  14. Replies
    45
    Views
    2,232

    Hello every Today I run it and it just want...

    Hello every

    Today I run it and it just want to turn off and I don't know why. The rpm rev up down for few seconds and then it shutoff and if I hold the throttle to keep it on 1000 rpm it vibrate....
  15. Replies
    45
    Views
    2,232

    Injectors seized like member say

    Hi,

    Today, I buy the new fuel pump from the dealer and I install it but the engine not work after that I check the spark plug not wet (no gas on it). So, I pull the injectors to local car workshop...
  16. Replies
    45
    Views
    2,232

    I check the fuel pump and it's not working and...

    I check the fuel pump and it's not working and the coil is short :(
  17. Replies
    45
    Views
    2,232

    Here how is my fuel pump screen and fuel tank...

    Here how is my fuel pump screen and fuel tank look like, Now I will check it with 12 v battery after clean it

    http://greenhulk.net/forums/attachment.php?attachmentid=457142&stc=1
    ...
  18. Replies
    45
    Views
    2,232

    I check today the coil all have spark. The...

    I check today the coil all have spark. The problem is fuel pump not prime gasoline to the injectors and now I try to remove the fuel pump to check it
  19. Replies
    45
    Views
    2,232

    Maybe like you say because they siting in the...

    Maybe like you say because they siting in the shelf for 1 year from 6 Jan 2019 until today I install everything and try to start it with ''bAt'' sign in the cluster.

    I will check tomorrow morning...
  20. Replies
    45
    Views
    2,232

    I clean the intercooler coil with small needle to...

    I clean the intercooler coil with small needle to smash the salt in between and it pass the leak test. Today,I install everything after full rebuild engine (new crankshaft,new connecting rod, new...
  21. Replies
    45
    Views
    2,232

    I will make an leak test to check if there any...

    I will make an leak test to check if there any leaks in the intercooler.
    But, If it pass the leak test is this mean it's in good condition and I don't need to change the intercooler anymore?
    ...
  22. Replies
    45
    Views
    2,232

    You mean these spray cans for cleaning the coil ...

    You mean these spray cans for cleaning the coil :

    http://greenhulk.net/forums/attachment.php?attachmentid=456894&stc=1

    http://greenhulk.net/forums/attachment.php?attachmentid=456895&stc=1
    ...
  23. Replies
    45
    Views
    2,232

    I don't know because I buy it as not working and...

    I don't know because I buy it as not working and owner ask me it sink before but he repaired it.

    thank you
  24. Replies
    45
    Views
    2,232

    Ultra 250x final step !!!

    Hi,

    I finish engine rebuild and now before install engine I remove the intercooler and this what is inside it :

    http://greenhulk.net/forums/attachment.php?attachmentid=456868&stc=1
    ...
  25. Replies
    2
    Views
    308

    Ok,I buy the both front bearings from the dealer...

    Ok,I buy the both front bearings from the dealer but, it's normal that the bearing move free not tight in the impeller shaft when I fit them ?
Results 1 to 25 of 97
Page 1 of 4 1 2 3 4