Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    115

    I can tell you from my limited wake jumping...

    I can tell you from my limited wake jumping experience......keep the belly flops to a minimum. You want to land a bit nose up. The pump will break the water and the machine will land softly. Let off...
  2. Replies
    17
    Views
    14,918

    I commonly see compression come up 10-15psi after...

    I commonly see compression come up 10-15psi after proper break-in.
  3. Something else is going on. Maybe dirty...

    Something else is going on. Maybe dirty injectors, faulty IAC or TPS, or something internally like bad valve seals (leakdown test). After it fowls a set post some up close shots so we can see what...
  4. What he said. The only fuel injected 2...

    What he said.

    The only fuel injected 2 stroke that can be premixed is the 1300 GPR bacause the fuel injectors are at the air intake and the whole engine will still get lubed.

    When the fuel...
  5. Replies
    3
    Views
    115

    Wait.........are you thinking a GTX could...

    Wait.........are you thinking a GTX could actually 'jump' a wave? .........Maybe if they're breaking 4ft plus (ocean)....on freshwater, no way.
  6. Replies
    7
    Views
    240

    I also use that technique to fill the carbs after...

    I also use that technique to fill the carbs after a cleaning or overhaul.
  7. Replies
    7
    Views
    240

    Don't rev it, pull the choke and use the choke to...

    Don't rev it, pull the choke and use the choke to keep the idle down until the carbs fill with fuel. They commonly do that right after a carb overhaul cause the carbs are dry. If the choke doesn't...
  8. Replies
    12
    Views
    3,800

    120psi is what I see on most 66v engines in good...

    120psi is what I see on most 66v engines in good shape. Low hours are great, BUT....it's the age that kills these. One of those oil lines could pop off literally any minute!!! I have a pretty clean...
  9. I doubt that's a nick. That's right about where...

    I doubt that's a nick. That's right about where one of the screws goes that holds the ring. Probably just got drilled all the way through.....it's a non issue.
  10. Replies
    2
    Views
    146

    When it started getting good.....

    2003, Seadoo released the GTX Limited Supercharged with 185hp!!! A customer of mine just bought these matching twins from an older fellow. They need a good detailing as they've been sitting unused...
  11. Replies
    11
    Views
    503

    Bad news bubba.....the rear shaft bearing seized...

    Bad news bubba.....the rear shaft bearing seized up and snapped that shaft. Also looks like it ruined the SC housing. You'll need to pull the engine so you can remove the PTO housing and find the...
  12. Just do like all my customers and don't maintain...

    Just do like all my customers and don't maintain anything 'til it breaks, lol!!
  13. Replies
    18
    Views
    862

    The one directly under the air compressor returns...

    The one directly under the air compressor returns to the oil tank. You'll probably need to clean the oil out of all the RAVE tubing too........and don't forget to hook that up BEFORE the engine is...
  14. I get 'em in stock at the local auto parts house....

    I get 'em in stock at the local auto parts house. I'll check up on the part number.
  15. Thread: 2002 1100 Di

    by Myself
    Replies
    9
    Views
    200

    Have you verified TPS voltage is smooth with no...

    Have you verified TPS voltage is smooth with no dead spots while slowly moving throttle?
  16. Replies
    18
    Views
    862

    Yes, pointed straight up. look for a tee at the...

    Yes, pointed straight up. look for a tee at the RAVE solenoid. Line with check valve goes to that. It's just a vent.
  17. Replies
    4
    Views
    358

    If the ECU is from an '05 215 then it should work.

    If the ECU is from an '05 215 then it should work.
  18. Replies
    18
    Views
    862

    Brass nipple......there is a vent line with a...

    Brass nipple......there is a vent line with a check valve going to a T right by the RAVE solenoid.
  19. Replies
    9
    Views
    214

    If they're not tweaked too bad I just bend 'em...

    If they're not tweaked too bad I just bend 'em back cold with a Cresent wrench.
  20. Replies
    17
    Views
    1,814

    I believe it's a 1/4" socket and I hammered it a...

    I believe it's a 1/4" socket and I hammered it a bit to 'egg' it. Fits on most oil pumps. Just used it on a Seadoo 951 Di the other night.
  21. Thread: Yamaha remote

    by Myself
    Replies
    3
    Views
    151

    Don't have one for our FXHO Cruiser and never...

    Don't have one for our FXHO Cruiser and never did......though we've not put that many hours on it either.
  22. Replies
    9
    Views
    214

    Run it. Yamaha acceptable clearances are...

    Run it. Yamaha acceptable clearances are .008-.024.
  23. Replies
    2
    Views
    213

    Normally it's because when the engine blew up...

    Normally it's because when the engine blew up some metal bits get smashed in between the oil pump gears and mess them up. I've used many WSM oil pumps for the 4tecs and never had any issues. There...
  24. Replies
    11
    Views
    289

    I pull 'em out of every one I work on. Idle it...

    I pull 'em out of every one I work on. Idle it around a solid 5 minutes, then ride easy another 5 minutes......good to go. Unless your riding 50* water, then add a restrictor or ball valve. Many...
  25. Here's an Ultra 150 manual. Same thing, different...

    Here's an Ultra 150 manual. Same thing, different hull.--->http://www.mediafire.com/file/inwydzcz2jm/Kawasaki_Service_Manual_Ultra-150.pdf/file
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4