Search

Type: Posts; User: steve45

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. WD-40 is garbage. It will dry out and get...

    WD-40 is garbage. It will dry out and get sticky. Suggest you clean it with solvent and use a lubricant, not a Water Dispersant.
  2. Replies
    25
    Views
    205

    Welcome aboard, YSLD7! The $3K price with...

    Welcome aboard, YSLD7!

    The $3K price with double trailer is good, if they 'Skis are good. As everyone has mentioned, running on the trailer really doesn't mean anything except that the ignition...
  3. Replies
    6
    Views
    134

    Hope you've got the extended warranty.

    Hope you've got the extended warranty.
  4. Replies
    4
    Views
    81

    They are, indeed, different. I had a '98 and a...

    They are, indeed, different. I had a '98 and a '99 and wanted to swap parts to do some troubleshooting, but couldn't. Harness connectors are different, ignitor connectors are different, etc.
  5. Spray it with oil to preserve it until you have...

    Spray it with oil to preserve it until you have time to assemble it.
  6. Replies
    4
    Views
    69

    I don't know, but I would try this: ...

    I don't know, but I would try this: ...
  7. Replies
    8
    Views
    121

    Welcome aboard, bkirby4965! If your hull...

    Welcome aboard, bkirby4965!

    If your hull identification number is 41803 or below, you need the special spark plugs, NGK R6918C-9.

    Pop-off pressure should be about 15 PSI.

    If it's been...
  8. So when you had the fuel pump out, did you clean...

    So when you had the fuel pump out, did you clean ALL the crud out of the tank? I would assume that when you replaced the pump you also replaced the filter sock, right?
  9. Replies
    2
    Views
    62

    Welcome aboard, FL_Rider! They're proprietary....

    Welcome aboard, FL_Rider!

    They're proprietary. The fuel rail O-rings also fit the needle seat. Don't know about the mixture screw O-rings.

    I've been running some Viton O-rings that are...
  10. Replies
    19
    Views
    347

    Bearings? What bearings? I don't see any...

    Bearings? What bearings? I don't see any bearings.
  11. Replies
    1
    Views
    93

    No need to ask the same question in multiple...

    No need to ask the same question in multiple places. It just confuses everybody.
  12. Replies
    5
    Views
    164

    When I had 'Skis with caps that were mounted...

    When I had 'Skis with caps that were mounted close to the water, I replaced the with aftermarket metal caps I bought on Ebay. No more problems with cracking.

    You can use an inspection camera to...
  13. Replies
    2
    Views
    88

    I'd measure the distance between the motor mount...

    I'd measure the distance between the motor mount holes in the hull and on the motor mount. Then I'd place a straight edge across the rear mounting holes in the hull and measure from that to the...
  14. Replies
    2
    Views
    65

    Welcome aboard, 03 kawasaki Stx-12f! Sounds...

    Welcome aboard, 03 kawasaki Stx-12f!

    Sounds like the reverse gate is hanging down a little too far. Try adjusting it up slightly and see if that helps.
  15. Replies
    118
    Views
    5,831

    After reading through this thread, I decided to...

    After reading through this thread, I decided to buy a couple of the reed valves to install on my Ultra LXs. However, it appears that they may not fit properly. I pulled the exhaust outlet off of...
  16. Replies
    37
    Views
    483

    Ummm... Yes!

    Ummm... Yes!
  17. Replies
    4
    Views
    118

    http://greenhulk.net/forums/showthread.php?t=27571...

    http://greenhulk.net/forums/showthread.php?t=275714
  18. Replies
    4
    Views
    118

    There is at least one place that has been...

    There is at least one place that has been mentioned here that can match keys to your ECU without an existing key, but I can't remember the name. Do a search on this site.
  19. Replies
    2
    Views
    84

    100 PSI sounds low, however, I'd look deeper into...

    100 PSI sounds low, however, I'd look deeper into the fuel system if it's not getting fuel. Look at the fuel pickup screens inside the tank. I pull the out and replace with rubber hose of the same...
  20. Replies
    1
    Views
    81

    Welcome aboard, Dean! Read the last post in...

    Welcome aboard, Dean!

    Read the last post in this thread: http://greenhulk.net/forums/showthread.php?t=277981

    Then read this: http://greenhulk.net/forums/showthread.php?t=277981
  21. The gold colored part is a relay. A solenoid s a...

    The gold colored part is a relay. A solenoid s a device that pushes the starter pinion into the flywheel. A relay is simply a high current switch that is operated by a low current circuit. JetSkis...
  22. Replies
    5
    Views
    92

    This 'Ski doesn't have a computer nor codes. Nor...

    This 'Ski doesn't have a computer nor codes. Nor will it get 'stuck' in limp mode.

    When you installed the temp sensor, did you put grease in the hole? It needs a fluid to conduct heat to the...
  23. Replies
    20
    Views
    332

    Where are you located bmj?

    Where are you located bmj?
  24. Replies
    4
    Views
    117

    The starter relay is in the box. It has two...

    The starter relay is in the box. It has two large studs that stick out the side marked 'Battery' and 'Starter'.
  25. Replies
    4
    Views
    117

    I'm guessing that you turned on the orange...

    I'm guessing that you turned on the orange switch, right? Open the round black cover on the electrical box and check the fuses.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4