Search

Type: Posts; User: mwhc

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Looks to be the fairly standard #2-3 cylinder...

    Looks to be the fairly standard #2-3 cylinder lean/timing issue. It's well known bc of the manifold setup those cylinders get the most air (run leaner). along with pulling some timing in 2&3 heres...
  2. Replies
    28
    Views
    1,235

    Also I've had them pack up more expensive items...

    Also I've had them pack up more expensive items before and STILL hassle me for damages trying to say the damage was done before the box broke open and obviously hit the ground [emoji23][emoji23]
  3. Replies
    30
    Views
    906

    Should work like this if you read it 1 way......

    Should work like this if you read it 1 way... install the jumper on 1,2,3 and remove it on #4. #4 will be the one you plug into the maptuner......

    If that doesnt work it would have to be the...
  4. Replies
    30
    Views
    906

    They mention a termination jumper.... is that...

    They mention a termination jumper.... is that installed correctly?
  5. Thread: E85 Tune

    by mwhc
    Replies
    8
    Views
    2,794

    Yup, maptuner can do all that

    Yup, maptuner can do all that
  6. Replies
    30
    Views
    906

    Where's all the power cords?457427

    Where's all the power cords?457427
  7. Replies
    30
    Views
    906

    Plug the power cords in..... hahaha sorry that's...

    Plug the power cords in..... hahaha sorry that's all I could see
  8. Thread: Leak down test

    by mwhc
    Replies
    18
    Views
    507

    No you'll need new head bolts

    No you'll need new head bolts
  9. Thread: Leak down test

    by mwhc
    Replies
    18
    Views
    507

    You wont need new valves unless you want to...

    You wont need new valves unless you want to upgrade them. You can just lap them back in or have a shop give it a valve job reassemble with your new springs/retainers. It's doubtful you need rings...
  10. Thread: Leak down test

    by mwhc
    Replies
    18
    Views
    507

    If you have (and you do) the rockershaft off all...

    If you have (and you do) the rockershaft off all the valves are closed... does it matter if the piston is at TDC, maybe a bit but if you're leaking air past the valves its kinda a mute point where...
  11. Thread: Leak down test

    by mwhc
    Replies
    18
    Views
    507

    Exhaust valves take a beating on these...

    Exhaust valves take a beating on these supercharged engines. You're having a hard enough time changing out the springs you may as well just take the head off at this point. You'll need some new...
  12. Thread: FS: Maptuner X

    by mwhc
    Replies
    1
    Views
    309

    SOLD I'll take it message sent

    I'll take it message sent
  13. Replies
    30
    Views
    1,092

    Looking at it again it looks like the chain is...

    Looking at it again it looks like the chain is slack on the exhaust cam so maybe you didnt have the tensioner in at that point which would have pulled that intake cam back to where it should be once...
  14. Replies
    30
    Views
    1,092

    I know it's hard to tell from the pictures on the...

    I know it's hard to tell from the pictures on the internet but that intake cam looks off a bit to me. In my experience they're usually hard to tell if the lines are 100% level but just barely, to me...
  15. Replies
    30
    Views
    1,092

    Timing right?

    Timing right?
  16. Replies
    22
    Views
    530

    Just lock the crank then it wont move. you'll...

    Just lock the crank then it wont move. you'll need to do that to put the cans back in anyway
  17. Replies
    22
    Views
    530

    It's a missing tooth on purpose. Ecu uses it...

    It's a missing tooth on purpose. Ecu uses it along with cam sensor to "count" and know where the engine is at in regards to firing
  18. Replies
    4
    Views
    166

    Yea thats the adapter. Usually it's easier to...

    Yea thats the adapter. Usually it's easier to buy the new stinger piece that screws into that then to try and swap them.... look at the instructions you'll see what I mean.

    Not sure exactly what...
  19. Replies
    4
    Views
    166

    Baby steps though, none of that it rocket science...

    Baby steps though, none of that it rocket science just a little clunky how it has to be done IMO
  20. Replies
    4
    Views
    166

    You need to do some searching..... riva/aquasport...

    You need to do some searching..... riva/aquasport make an o2 adapter that goes in the pipe. You pay for the data logging option, riva enables it on your tuner, you log with your map tuner (gotta...
  21. Replies
    2
    Views
    79

    Jesus has something with the cams for sure. Data...

    Jesus has something with the cams for sure. Data logging will always clean up the tune for your setup
  22. Let us know how you do with the sho.... there's...

    Let us know how you do with the sho.... there's something in my buddies (and I have heard of others) that they get stuck around 83-84mph. For some reason we've logged, and cant figure out why, itll...
  23. Replies
    81
    Views
    13,048

    Nah man, at worst he got some bad info forwarded...

    Nah man, at worst he got some bad info forwarded to him. He's a middle man and never steered anyone wrong for the last 14yrs or so. Hell even told me many o times to not buy parts bc they wouldn't...
  24. Replies
    81
    Views
    13,048

    Gotta be (obviously from the pictures) some sort...

    Gotta be (obviously from the pictures) some sort of taper from the front (driveshaft/wear ring side is) to where the rear (tail cone/exit nozzle is)..
    To me it looks clear the lip just past the...
  25. Did you send him an email? It's the holidays so...

    Did you send him an email? It's the holidays so response may be slow but as much as I've bothered him with a PITA ski he always tried to help....
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4