Search

Type: Posts; User: Rodsatheart

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    72
    Views
    4,906

    HMMMM ...

    HMMMM
    ...
  2. Replies
    4
    Views
    122

    That's how I align mine, but use a feeler gauge,...

    That's how I align mine, but use a feeler gauge, and check vertical and horizontal alignment.
  3. Replies
    4
    Views
    89

    If you want to be able to tune, get a set of 1100...

    If you want to be able to tune, get a set of 1100 cdk carbs and rebuild them. They may just need new gaskets. Were the plugs covering the mixture screws removed ?
  4. Replies
    4
    Views
    122

    Did you align the engine when you reinstalled it...

    Did you align the engine when you reinstalled it ? might pull the pick up from the tank and look to see if it has the filters on the tubes. If so, they may be plugged.
  5. I want your ski !!!!!!!!!!!! I take charity...

    I want your ski !!!!!!!!!!!! I take charity donations. :lmao:
  6. Thread: Beaching

    by Rodsatheart
    Replies
    5
    Views
    280

    I don't beach, at least if it can be avoided. We...

    I don't beach, at least if it can be avoided. We all have mooring setups to keep the skis well off the shore.
    Looked up the Wetlander. That stuff sounds awesome. Have a Stx I was getting ready to...
  7. Do a compression check. It wont take any time...

    Do a compression check.
    It wont take any time at all to fill the lines, filter and carb, in fact, it will prob fill when you prime it with a little premix. The other thing you need to do is replace...
  8. Replies
    72
    Views
    4,906

    :lmao:

    :lmao:
  9. Run you thumb nail across it. If you feel the...

    Run you thumb nail across it. If you feel the slightest imperfection, have it replated or replace it. It's the crank bearing that are in question. If they go out, that engine will be toast top to...
  10. Replies
    72
    Views
    4,906

    Completely agree. They have a tried and true line...

    Completely agree. They have a tried and true line up. When everyone else was screwing around with hull repair from thin, light weight materials, Kawi owners were out hammering the hell out of...
  11. Replies
    1
    Views
    88

    1 turn out high and low, 25psi pop off.

    1 turn out high and low, 25psi pop off.
  12. Replies
    102
    Views
    4,254

    :smt042:smt042:smt042

    :smt042:smt042:smt042
  13. Replies
    14
    Views
    411

    That spring is inside the fitting/nipple/outlet....

    That spring is inside the fitting/nipple/outlet. It comes out of the pump and make a 90 degree bend.
  14. Replies
    3
    Views
    134

    First place to start would be the battery. Make...

    First place to start would be the battery. Make sure it is fully charged, and cranking voltage is staying above 11, and snaps right back to 12volts when you let off the button. Check voltage when...
  15. Might very carefully pull that injector and see...

    Might very carefully pull that injector and see if it's not sealing to the head. Check the pintle and the seat for carbon, and/or nicks also.
    As far as the vibration, is it really a vibration or a...
  16. You lucked out. I remembered someone recently...

    You lucked out. I remembered someone recently saying they found one on ebay, so I looked, and here ya go. These are hard to come by. Get good kits, not the 25.00 ones. They will prob have a mesh...
  17. Replies
    1
    Views
    84

    If you have the arbors to reach in, you can clean...

    If you have the arbors to reach in, you can clean with a 60 or coarse grit roll. I would refrain for getting into the actual ports windows and screwing with the misalignment. Cleaning and polishing...
  18. Replies
    11
    Views
    383

    Prob. just the plugs. Replace all of them. These...

    Prob. just the plugs. Replace all of them. These things don't like to be run at low throttle for extended periods of time, and if that's going to be the norm, you might consider going to a hotter...
  19. Replies
    4
    Views
    192

    I don't think they are blind holes, but would...

    I don't think they are blind holes, but would have to go look at my 1100 hull to be sure.
    I would go get some stainless metric bolts, flat washer, and silicone, and seal the holes.
    I'm curious...
  20. Replies
    4
    Views
    192

    https://www.partzilla.com/product/kawasaki/11065-3...

    https://www.partzilla.com/product/kawasaki/11065-3712

    The inserts are for mounting a bording step.
  21. Replies
    14
    Views
    411

    View Post

    It's in the 90° fitting exiting the pump. Ypu can look into the hole with the cover off and see the spring. Aslo, the oring that shows in the part diagram is prob the oring that seals the discharge...
  22. Thread: CDK Kits

    by Rodsatheart
    Replies
    1
    Views
    119

    CDK Kits

    Since this issue is showing up again, thought I share this. This is a picture of the worst Keihin CDKII kits out there. This style diaphragm will have you chasing your tail, and you setting your low...
  23. Replies
    14
    Views
    411

    Found this, thought I'd share...

    Found this, thought I'd share it.http://greenhulk.net/forums/attachment.php?attachmentid=448488&stc=1
  24. Replies
    0
    Views
    100

    CDK pop off chart

    Just came across this, and thought I would share. Always been discussion on the CDK pop off's.
    http://greenhulk.net/forums/attachment.php?attachmentid=448487&stc=1
  25. Replies
    14
    Views
    411

    I could have sworn there is also a check ball. I...

    I could have sworn there is also a check ball. I have a couple of racks, and I'll check later. I would set the low speed screws to best idle and start, and work on the accelerator pump function. As...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4