Search

Type: Posts; User: vwztips

Page 1 of 6 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thank you sir

    Thank you sir
  2. Polaris OEM piston hole in side skirt question

    Have a 1996 Slt700. Having to rebuild the top end due to a water leak in a cooling line.

    The cylinders are part #3021009 (Hurricane cylinders). I found NOS pistons 0.50mm over on eBay from a boat...
  3. Replies
    4
    Views
    848

    FS - Parts 2001 Virage parts

    Well I stripped the ski of most all the useable parts and scrapped the hull. Here is a quick pic of what I recently stripped. Have other parts not pictured like single carb, pump extension, stock...
  4. Replies
    4
    Views
    1,203

    FS - Parts Still have parts. LMK what you need.

    Still have parts. LMK what you need.
  5. Replies
    0
    Views
    367

    FS 1994 Sea Doo SPI excellent condition

    My friend is selling his 1994 Sea Doo SPI with galvanized trailer. I remember him buying this ski new. Frankly it looks as good, or better, now than it did before he put it in the water for the first...
  6. Replies
    4
    Views
    1,203

    FS - Parts 2001 Virage part out

    Have a 2001 Virage that I am parting out.

    What is available:

    Complete reverse system from handle to bucket $100
    LR505 $50
    Mirrors - Left and Right $40
    MFI $100
    Electrical box $40
    Wiring...
  7. Replies
    0
    Views
    353

    FS - Parts Complete reverse system from 2001 Virage

    Parting out a 2001 Virage. HAve the complete reverse system from the ski for sale.

    PM me if interested.
  8. Replies
    3
    Views
    813

    WTB - Parts I have one. PM me

    I have one. PM me
  9. Answered my own question this weekend. The single...

    Answered my own question this weekend. The single carb was very flat starting out and then would take off. Switched over to the duals and it takes off as it should.
  10. Should i go with single carb or duals on my 96 SLT700

    Creating a Frankenstein 700 for my 96 SLT700 with parts I have on hand to rebuild my engine with.

    Have quite a few parts sitting in the shop so here is what I have put together so far.

    Bottom...
  11. Interesting because the 1996 SLTX and 1997...

    Interesting because the 1996 SLTX and 1997 Hurricane use the same cylinder part #3021009 which is really confusing me. The 2 good 3021009 cylinders I have came from a Hurricane. The spare SLTX 1050 I...
  12. Thanks, reason I was asking about the 009's is...

    Thanks, reason I was asking about the 009's is that the Hurricane twins also used the 009's and I have 2 sitting in my shop.
  13. Sorry I was not clear. Through this process it...

    Sorry I was not clear. Through this process it appears there is scoring on the Mag piston. The other one is fine. However it being a SBT motor it has their 82mm pistons. I did look last night and the...
  14. K447 you stated this early on in this thread. I...

    K447 you stated this early on in this thread. I did state this is an SBT engine so not sure which cylinders I have in this engine. Need to look at the outer stamping when I pull it back out. However,...
  15. What is difference between SLTX and SLT700 cylinders besides part #?

    Found one cylinder of my 700 cylinder with score marks MAG cylinder on the exhaust side. Still has 150 PSI on both cylinders. Out of precaution, looking to replace the cylinder, piston and rings with...
  16. Thank you very much for the info!

    Thank you very much for the info!
  17. Thanks for the tip on the connector....

    Thanks for the tip on the connector. Unfortunately I checked continuity on the yellow wire from the stator housing to the terminal plate in the box and it checked good. So it appears I need to swap...
  18. Erased double post

    Erased double post
  19. This ski started with just a gas gauge when I...

    This ski started with just a gas gauge when I bought it new. I installed the round MFI kit like the SLT750's had right after I bought it
  20. After further investigation it appears my stator...

    After further investigation it appears my stator is not charging. No change in battery voltage when cranked. Checking ohms across yellow and R/B shows open.

    PO let stator cable ride on the...
  21. Nevermind, found answer

    Nevermind, found answer
  22. Will do. So to recap: I put the 448 CDI in...

    Will do.

    So to recap:

    I put the 448 CDI in after my MFI would not wake up when engine was started and showed no RPM's with the 558.
    With the 448 the MFI operates normally but no RPM,...
  23. I have no history on the engine other than is has...

    I have no history on the engine other than is has been rebuilt by SBT. It has 150 PSI on both cylinders. The oil injection has been removed. It was dead on 20 degrees BTDC with the 558 CDI and now is...
  24. So installed the Virage carbed 700 in my 96...

    So installed the Virage carbed 700 in my 96 slt700. Used the single carb, 558 CDI and stator that came in the virage. It fired right up. Only have 2 issues. The MFI did not wake up when started (I...
  25. Replies
    1
    Views
    821

    I have a complete Gen 3 setup for the 700 motor....

    I have a complete Gen 3 setup for the 700 motor. Stator, CDI box (448) and coil pack
Results 1 to 25 of 149
Page 1 of 6 1 2 3 4