Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    1,154

    Skat 155 or kawi 155? Sean

    Skat 155 or kawi 155?

    Sean
  2. Replies
    1
    Views
    82

    Nope, the ultras are 155mm or 160mm and the stx...

    Nope, the ultras are 155mm or 160mm and the stx is 148mm

    Sean
  3. Replies
    2
    Views
    194

    FS - Parts pics? what engine is it for? Sean

    pics? what engine is it for?

    Sean
  4. Replies
    21
    Views
    1,824

    Beerdart stuck a 4tec in his. Sean

    Beerdart stuck a 4tec in his.

    Sean
  5. Replies
    21
    Views
    1,824

    Nice score Steve! I have been looking on an off...

    Nice score Steve! I have been looking on an off for one for a while.

    Sean
  6. Replies
    4
    Views
    206

    WTB - Parts Going to need to know more about what ski it is. ...

    Going to need to know more about what ski it is.

    Sean
  7. Replies
    12
    Views
    864

    Im not assuming anything. Speaking from...

    Im not assuming anything. Speaking from experience, even on the neglected motors that I have torn down where the hulls sat with water in them or on the water in floating docks, corrosion inside the...
  8. Replies
    12
    Views
    864

    Any motor I have opened has been damn near...

    Any motor I have opened has been damn near spotless inside, even neglected ones. Unless you sink the ski, crack a head, or pop an oil cooler you aren't really going to get water in the cases. The...
  9. Replies
    7
    Views
    599

    FS - Parts Nope, sorry. Sean

    Nope, sorry.

    Sean
  10. Replies
    18
    Views
    1,491

    Start by adding a shim/washer between the hull...

    Start by adding a shim/washer between the hull mounts and the plate at the rear to adjust the angle of the plate.

    I ground the mounts for the plate down so the front of the plate was flush or...
  11. Replies
    18
    Views
    1,491

    Thanks, I am reasonably happy with how they...

    Thanks, I am reasonably happy with how they turned out. A couple notes on them, make sure you round any edges on them, bashing your shin on a sharp piece of aluminum under the water line sucks ass. ...
  12. Replies
    18
    Views
    1,491

    What is your goal for the tabs? Sean

    What is your goal for the tabs?

    Sean
  13. Replies
    18
    Views
    1,491

    Yep, mine is all doo, I mostly meant to look for...

    Yep, mine is all doo, I mostly meant to look for where I have mine mounted and attached.

    Sean
  14. Replies
    18
    Views
    1,491

    Take a look at my kawidoo thread, there are (or...

    Take a look at my kawidoo thread, there are (or should be) some pictures of the vts install.

    Sean
  15. Replies
    18
    Views
    1,491

    easiest method would be to use a yamaha quick...

    easiest method would be to use a yamaha quick trim setup or set it up as an auto drop.

    Sean
  16. Ok cool, its been a while since I played with the...

    Ok cool, its been a while since I played with the stock setup. My megasquirt primes on key-on so I wasn't 100% sure. On my 12f, I used to just bump the starter button and let the pump prime if I had...
  17. Its been a while since I ran the stock ecu but if...

    Its been a while since I ran the stock ecu but if my memory is right, the fuel pump only kicks on when you hit the starter button for a few seconds.

    Sean
  18. Replies
    7
    Views
    599

    FS - Parts Triple Fuel Pickup Sold Sean

    Triple Fuel Pickup Sold

    Sean
  19. Replies
    14
    Views
    909

    Yeahhhhh we can't see anything from the pictures....

    Yeahhhhh we can't see anything from the pictures.


    What jet pump are you running? It may be producing a more rapid engine decel when the pump loads back up.

    Sean
  20. No need to apologize, we all gain when people...

    No need to apologize, we all gain when people share their experience.

    Sean
  21. Wax did a limited run so they may or may not be...

    Wax did a limited run so they may or may not be any left.

    My only complaint with the bed plate is that the clearance on the motor mounts is a little tight but that could be due to the rhaas...
  22. Replies
    3
    Views
    303

    The only aftermarket tunes that I know of that...

    The only aftermarket tunes that I know of that riva did for the stx were race gas only.

    One set was for the supercharges motors, and one set was for the high compression motors.

    Sean
  23. Replies
    3
    Views
    303

    I think the immobilizers are different, the cam...

    I think the immobilizers are different, the cam position nub is in a different spot relative to the crank angle on the early vs later models. The temp sensor curves are also different early vs late...
  24. Much appreciated, the camera hides most of the...

    Much appreciated, the camera hides most of the flaws but I keep telling myself that its a 33 year old standup, its okay for it not to be perfect. I am hoping to get some more work done on the hull...
  25. Replies
    6
    Views
    345

    The fuel system likes to corrode and take out the...

    The fuel system likes to corrode and take out the injectors, check for rust in the tank and plan on replacing the pump, filter, and reg. Budget for spark plugs, and fuel injector cleaning. The iac...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4