Search

Type: Posts; User: Shadyraro

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    33
    Views
    2,161

    GP1300 stuffed piston

    Thanks for all your input.
    Iím going to check out a crankshaft, jug and head from a guy who pulled down his 1300 recently. If all is good then Iíll order new pistons and a gasket set.
    Also Iíve...
  2. Replies
    33
    Views
    2,161

    Yeah I realise that but what defines a damaged...

    Yeah I realise that but what defines a damaged bearing? The roller pins do not look damaged at all, the rest of the bearings look good also.
    I even temp fitted it inside the case and it ran smooth...
  3. Replies
    33
    Views
    2,161

    480136

    480136
  4. Replies
    33
    Views
    2,161

    GP1300 stuffed piston

    Thanks for your input, Iíve decided not to remove them now as I really donít see any point. The seals all look brand new, and all the bearings are moving freely. What I did notice tho when I removed...
  5. Replies
    33
    Views
    2,161

    So today I got the crankshaft onto the bench to...

    So today I got the crankshaft onto the bench to give it a proper inspection. I sprayed some wd40 into the bearings to try loosen them up and they did. All bearings move freely but Iím not sure if...
  6. Replies
    33
    Views
    2,161

    GP1300 stuffed piston

    So I pulled the engine and stripped it down, and Iíve found that the centre connecting rod big end bearing has seized, so basically the crankshaft is now junk.
    Iím not sure what Iím going to do...
  7. Replies
    4
    Views
    481

    Thanks for the feedback, I have a fuel controller...

    Thanks for the feedback, I have a fuel controller so maybe thats not set correctly.
  8. Replies
    33
    Views
    2,161

    Also the ski has an EJK fuel controller which...

    Also the ski has an EJK fuel controller which I've never touched since I bought the ski as it was running fine or so I thought, and I don't even know if it's set correctly.
  9. Replies
    33
    Views
    2,161

    Thanks for the feedback, it looks like i'm...

    Thanks for the feedback, it looks like i'm pulling the engine.
    I was really trying to avoid pulling the bottom end but i guess there's no point rebuilding the top end if the bottom has issues.
    Is...
  10. Replies
    33
    Views
    2,161

    I'll check for corrosion and have a look at the...

    I'll check for corrosion and have a look at the anodes tomorrow, should they be clearly visible?
    The middle cylinder did have water in the crank, the base and head gaskets didn't look that bad so...
  11. Replies
    33
    Views
    2,161

    I'm happy to do it myself, I have a printed copy...

    I'm happy to do it myself, I have a printed copy of the manual at home so should be ok.
    I'm really trying to avoid pulling the bottom end out, I haven't looked into it thoroughly yet as I've been...
  12. Replies
    33
    Views
    2,161

    480027

    480027
  13. Replies
    33
    Views
    2,161

    GP1300 stuffed piston

    Thanks WFO, looks like an engine removal is on the cards. I took a couple more pics of the cylinders that might help to view the sleeve.
    I got quoted 5k for a full engine rebuild in Australia which...
  14. Did you figure out the problem?

    Did you figure out the problem?
  15. Replies
    33
    Views
    2,161

    View Post

    Iím not sure if itís sleeved or not, how can you tell?
    Also do you think the head is repairable? It has quite a bit of pitting on it.
    Now Iím wondering if I need to pull the motor to check the...
  16. Replies
    33
    Views
    2,161

    View Post

    Youíre spot on WFO, safe to say that jug is stuffed?

    479974
  17. Replies
    33
    Views
    2,161

    View Post

    Yeah Iíll look at doing that, what about the head do u think itís salvageable?
    I also noticed a little it of water in cylinder 2ís crankcase, maybe a seal gone?
  18. Replies
    33
    Views
    2,161

    479961

    479961
  19. Replies
    33
    Views
    2,161

    479960

    479960
  20. Replies
    33
    Views
    2,161

    GP1300 stuffed piston

    Did a compression test this morn to find cylinders 1 and 3 all good at 120psi, but cylinder 2 had 0 psi.
    So I pulled the head and found out why it was at 0, one stuffed piston with a damaged jug...
  21. Replies
    4
    Views
    481

    GP1300 Spark Plugs

    Thoughts on these plugs?
    L-R 1,2,3
    2005 GP1300479920
  22. Replies
    4
    Views
    364

    Whoever installed the hole shot on mine filled in...

    Whoever installed the hole shot on mine filled in the hole [emoji2375]
  23. Replies
    4
    Views
    364

    My lower sensor was removed for the hole shot...

    My lower sensor was removed for the hole shot mod, and the exhaust sensor was removed for the D plate mod. So I donít have any working sensors just resistors, but yeah it got me thinking about what...
  24. Replies
    4
    Views
    364

    GP1300 ohm resistors

    Just a question re ohm resistors for a 2005 1300. If you have the 2.2k resistor for the exhaust temp sensor installed and the 10k resistor for the water cooling sensor installed, is this a bad thing...
  25. Replies
    15
    Views
    1,380

    Did you end up resolving the issue?

    Did you end up resolving the issue?
Results 1 to 25 of 66
Page 1 of 3 1 2 3