Search

Type: Posts; User: toxicgun

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    480

    FS location?

    location?
  2. Thread: 215 flywheel

    by toxicgun
    Replies
    1
    Views
    128

    WTB got one for $100 if you still need one.

    got one for $100 if you still need one.
  3. for sure has been hydrolocked, you probably have...

    for sure has been hydrolocked, you probably have a bent rod, you will know in about 8-10 hours of riding. I would bust out a dial indicator and check for a bent rod.
  4. Replies
    9
    Views
    632

    FS - Parts that sucks balls

    that sucks balls
  5. Replies
    4
    Views
    363

    WTB - Parts how much are you asking?

    how much are you asking?
  6. spark, fuel, and compression, which one are you...

    spark, fuel, and compression, which one are you missing? I agree with above, sounds like it was sank and they cranked the piss out of it. May want to check that the rods arent bent from hydrolocking
  7. Replies
    0
    Views
    79

    WTB - Parts gp1200r stainless steel intake grate

    cash on hand, need one ss800 intake grate is the one I am looking for
  8. Replies
    9
    Views
    632

    FS - Parts looks like a pretty decent deal but that chipped...

    looks like a pretty decent deal but that chipped blade is going to be a problem. Replace the center section whomever buys it.
  9. that engine was under water it looks like. Check...

    that engine was under water it looks like. Check the casting numbers, it may be an older engine someone put in that ski. The older engines had sodium filled valves that liked to snap off.
  10. Replies
    2
    Views
    299

    SOLD did you take a roloc wheel to the gasket area? ...

    did you take a roloc wheel to the gasket area? Looks like circular swirls from a roloc or sander of some sort
  11. my gpsho ran 78gps on a completely stock setup...

    my gpsho ran 78gps on a completely stock setup with no tune with a 14/21 and I am pretty sure it is sitting on the rev limiter.
  12. Thread: Gp1200r parts

    by toxicgun
    Replies
    11
    Views
    656

    FS - Parts is the intake grate stainless or aluminum?

    is the intake grate stainless or aluminum?
  13. Replies
    13
    Views
    976

    it will technically run but not correctly at all....

    it will technically run but not correctly at all. I have personally tried it.
  14. Replies
    1
    Views
    152

    WTB - Parts standard bore?

    standard bore?
  15. Replies
    7
    Views
    301

    balance technology in livermore california does...

    balance technology in livermore california does mine.
  16. Replies
    3
    Views
    192

    Thanks, being that it is your old setup I will...

    Thanks, being that it is your old setup I will take your advise. I was planning on trying .020 but I will go with what you were doing since that was working.
  17. Replies
    3
    Views
    192

    4tec turbo guys spark plug gap question

    anything past 18psi is stumbling, I am suspecting the factory gap is too much. What are you guys running? Of course I have done new plugs and coils, doesnt seem to matter. running 11.5 currently...
  18. WTB so you want to exchange your old parts for the...

    so you want to exchange your old parts for the parts you need? Just modify the sho exhaust pipe yourself, use the rest of the 1200/1300 exhaust with it.
  19. Yep, I tried that, sucked down under boost.

    Yep, I tried that, sucked down under boost.
  20. Replies
    4
    Views
    533

    from what I recall the 2001 gp1200r was the...

    from what I recall the 2001 gp1200r was the preferred hull. Supposedly stronger and lighter. I have built two with 2001 hulls.
  21. is that kanaflex for an intake or the ducting...

    is that kanaflex for an intake or the ducting from the front vents?
  22. you need to take off the intake manifold and dump...

    you need to take off the intake manifold and dump the water out of it before starting it, at least pull an intercooler hose and see if there is water sitting in the intercooler
  23. something is wrong, how is the supercharger...

    something is wrong, how is the supercharger clutch? With stock prop my gpsho hit 78mph on first test ride, sitting on the rev limiter. Sounds like it is down on power to struggle turning a 13/20
  24. it is a great upgrade to put the aluminum solid...

    it is a great upgrade to put the aluminum solid pump instead of the 02 plastic unit. 02 and 03 were plastic and with enough thrust they swell or crack under pressure. Any 04-08ish aluminum pump...
  25. SOLD Thanks Kamikaze, I will put it to great use.

    Thanks Kamikaze, I will put it to great use.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4