Search

Page 1 of 11 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    7
    Views
    279

    Check the thread in my signature. If you pull the...

    Check the thread in my signature. If you pull the pumps, don't crank the motor over with the starter. Only rotate the engine by hand.

    If the gauges are bad, I can flash the ecus to 2004 spec to...
  2. Replies
    77
    Views
    2,313

    I may have figured out a way to make control...

    I may have figured out a way to make control cable thru hull fittings for relatively little money.

    Start with a -10an bulkhead fitting and hard line nut.

    Drill the an fitting through with a...
  3. Simple and elegant. Nice work Sean

    Simple and elegant. Nice work

    Sean
  4. Replies
    23
    Views
    803

    Very clean install. Did you ground the wire to...

    Very clean install. Did you ground the wire to the gauge or to the ecu? I assume since the wire runs direct to the ecu you would drop the wire from the ecu to ground but lets confirm it.

    Sean
  5. Replies
    23
    Views
    803

    Ip66 not rated for submersion but rated for water...

    Ip66 not rated for submersion but rated for water jets. The buttons were the leak path I was worried about but they seem to have good quality seals. The weak point seems to be where the wiring goes...
  6. Replies
    23
    Views
    803

    No question. I will be using factory sumitomo...

    No question. I will be using factory sumitomo connectors.

    Sean
  7. No worries, thanks for checking. I will see if I...

    No worries, thanks for checking. I will see if I can find it on an old laptop I have collecting dust in a closet.

    I am specifically looking for pictures of an old zapata "seadoo" race boat that...
  8. Replies
    77
    Views
    2,313

    What am I made of money Mike? This mockup is...

    What am I made of money Mike? This mockup is getting printed on paper, glued to some mdf, cut out with a dull jig saw blade, and nailed together using "reclaimed" nails from my neighbors fence.
    ...
  9. Replies
    77
    Views
    2,313

    Quick and dirty mock up, green is the kawasaki...

    Quick and dirty mock up, green is the kawasaki stx shoe, blue is the adapter, yellow is the doo 159 pump.

    I am hoping I can get this water jet cut to rough size and then knock the rest out on the...
  10. Kawasaki uses the awab clamps on the exhaust for...

    Kawasaki uses the awab clamps on the exhaust for sure and I think for the boost tubes as well. Never had a problem with those.

    Sean
  11. Replies
    13
    Views
    535

    Checkout ape race parts. They make great parts...

    Checkout ape race parts. They make great parts and are probably less than riva.

    Sean
  12. Replies
    77
    Views
    2,313

    Thats the current plan, it simplifies the setup...

    Thats the current plan, it simplifies the setup as well rather than making the custom shaft on the first page.

    Sean
  13. Replies
    10
    Views
    635

    I have made the mistake of leaving a full tank of...

    I have made the mistake of leaving a full tank of fuel in before and wrecked a pump assembly, regulator, injectors and filter. The gas was treated and bought from a station with a high turnover rate...
  14. Replies
    2
    Views
    218

    Its worth paying for, it really is good software....

    Its worth paying for, it really is good software. There is also the option of setting up calculated fields if you want to go down a rabbit hole with advanced tuning.

    Sean
  15. Replies
    77
    Views
    2,313

    No kidding about the price, looks to be well made...

    No kidding about the price, looks to be well made stuff though.

    Sean
  16. Replies
    77
    Views
    2,313

    I don't plan on using the pto splines at all....

    I don't plan on using the pto splines at all. There is enough slop in them that if they weren't supported by the carrier and the the pump the end would flail around. The kawasaki coupler would make...
  17. Replies
    6
    Views
    350

    It was a link to a site that collated a bunch of...

    It was a link to a site that collated a bunch of ads for baitcaster reels. I removed the link.

    Sean
  18. New AEM 320lph fuel pumps, new NGK plugs, new OEM...

    New AEM 320lph fuel pumps, new NGK plugs, new OEM oil pressure switches, ARP flywheel bolts ordered.

    Going to keep cleaning these nasty skis up.

    Sean
  19. Replies
    123
    Views
    7,230

    Yep exactly. I clean the header with a piece of...

    Yep exactly. I clean the header with a piece of 1000/1500/whatever fine grit paper on a piece of glass then wipe it down with brake cleaner. Spray both sides of the gasket with copper spray, and...
  20. Replies
    4
    Views
    246

    The sender on the 15f and 12f uses multiple...

    The sender on the 15f and 12f uses multiple floats and they do go bad over time with poor quality fuel or water. Unfortunately its an oddball sensor range so oem is the best option for replacement. ...
  21. Its dead, the corrosion is only going to get...

    Its dead, the corrosion is only going to get worse. Odds are the prop and bearings are bent too.

    Sean
  22. Replies
    71
    Views
    3,906

    No problem, whats the point of a forum if we...

    No problem, whats the point of a forum if we don't have a positive and open discussion?

    I have been waiting for years to get schooled up on how to read these maps so I am stoked someone who does...
  23. Replies
    71
    Views
    3,906

    Yeah, the 03 and 04 12f ecus run 1 "water temp"...

    Yeah, the 03 and 04 12f ecus run 1 "water temp" sensor and do not have slo mode, the 04 15f ecu doesnt run slo mode but run 1"water temp" and 1 oil temp sensor.

    These engines just arent setup to...
  24. On the na motors, valve float shouldnt happen...

    On the na motors, valve float shouldnt happen until well over 10k since they are basically zx12r heads, with boost its a different story. Mike might know the limit since he runs a turbo setup but he...
  25. Replies
    28
    Views
    2,289

    On the rebuild really watch the oil rings on the...

    On the rebuild really watch the oil rings on the pistons, its really easy to have one pop off while installing the cylinders and get wedged between the piston and the bore. You won't notice until you...
Results 1 to 25 of 270
Page 1 of 11 1 2 3 4