Search

Type: Posts; User: king

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    225

    I think I found where the water get inside the...

    I think I found where the water get inside the hull but I don't know how this happen since I replace all these 4 seals include the ball bearing in middle with new one from KAWASAKI dealer before I...
  2. Replies
    4
    Views
    225

    Ultra 250x water inside !!!

    Hello everybody

    Yesterday I take my 08 ultra 250x and lift it from the trailer to the water but in less then 3 minutes without start it I open the seat to be sure everything is good because this...
  3. Thread: rpm surging

    by king
    Replies
    4
    Views
    286

    I checked the tps it works perfect the value it...

    I checked the tps it works perfect the value it gives exactly the same in service manual but I still not check the IAC because there is one of screw I can't open it was very tight and there is no...
  4. Thread: rpm surging

    by king
    Replies
    4
    Views
    286

    Yes, yesterday I hear it but it didn't work...

    Yes, yesterday I hear it but it didn't work because of low Fuel. Today when I refill it with fuel and it's run. I didn't focus on that IAC sensor sound.


    thank you
  5. Thread: rpm surging

    by king
    Replies
    4
    Views
    286

    rpm surging

    Hello everybody

    Today I run my 08 ultra 250x after I left it for 5 months. When I start it it work from first turn and idle fine with ​ rpm surge between 1270 - 1300 but after remove the flushing...
  6. Replies
    10
    Views
    1,000

    Mostly this happen in Ultra when the head cracked...

    Mostly this happen in Ultra when the head cracked but there is another thing then crack, you should check your cylinder head warp check if it's within the service limit.
  7. Replies
    0
    Views
    232

    ultra 300x stabilizer on 250x ?

    Hello everybody,

    I have ultra 250x and it stabilizer in both side was damaged and I found set of new ultra 300x stabilizer oem more cheaper.

    It will fit or there are different between them?

    ...
  8. Replies
    45
    Views
    3,597

    Thanks for all who help me. Finally the end of...

    Thanks for all who help me. Finally the end of story :)
  9. Replies
    45
    Views
    3,597

    Hello I reset the timing for 3rd time then it...

    Hello

    I reset the timing for 3rd time then it start without hold the throttle and t run really smooth but I have question about the rpm, It should be stable on 1300 right ?
    Because mine rpm...
  10. Replies
    45
    Views
    3,597

    Yes, and I get same problem on the old timing...

    Yes, and I get same problem on the old timing (before reset)
  11. Replies
    45
    Views
    3,597

    I think the problem is from tps or iac so,today I...

    I think the problem is from tps or iac so,today I check the tps and it work well also, for iac is same.

    Anyone now how can I solve this problem?
  12. Replies
    45
    Views
    3,597

    I run it now it work just few second then it...

    I run it now it work just few second then it shutoff directly as you hold the throttle it work but the rpm is not stable and when remove my finger from throttle it will shutoff.
  13. Replies
    45
    Views
    3,597

    What I do is center punched without milled it...

    What I do is center punched without milled it flat so, when I drill it become one side very near to thread and other side little far from the thread then I use E-Z Out but when I tight it and turn it...
  14. Replies
    45
    Views
    3,597

    Hello everybody today, I try to make tdc by using...

    Hello everybody today, I try to make tdc by using the TDC gauge but the problem it is very hard to know if the mark on camshaft is aligned with the cylinder head.I adjust them but I am not pretty...
  15. Replies
    45
    Views
    3,597

    Hi, Because the collage closed now...

    Hi,

    Because the collage closed now <<<COVID-19. I return to work on my jet ski I receive the tdc gauge but the problem is the rod on the indicator is too short and now I try to make 120mm length...
  16. Replies
    45
    Views
    3,597

    I don't do anything because my collage holiday is...

    I don't do anything because my collage holiday is end so, I will come back and work on it next holiday.

    thank you Scottkrissinger for your interest
  17. Replies
    45
    Views
    3,597

    Ok, I will try to re-timing but, I need to use...

    Ok, I will try to re-timing but, I need to use TDC gauge because it is in the hull right? and after that I will upload the photo of it.

    Thank you Scottkrissinger
  18. Replies
    45
    Views
    3,597

    Yes, I count them it is 31 pins but the chain at...

    Yes, I count them it is 31 pins but the chain at exhaust cam always slack not go inside spoket and I don't no why

    thank you
  19. Replies
    45
    Views
    3,597

    Yes, the chain is slack always in exhaust cam...

    Yes, the chain is slack always in exhaust cam side I try to pull it then put the rest of chain on the intake cam but after I install the tensionor it jump again and become like the picture I don't...
  20. Replies
    45
    Views
    3,597

    I think yes, but can you see if it is right or...

    I think yes, but can you see if it is right or not ? and this is a photo of the timing I made before install the engine

    http://greenhulk.net/forums/attachment.php?attachmentid=457307&stc=1
    ...
  21. Replies
    45
    Views
    3,597

    Hello every Today I run it and it just want...

    Hello every

    Today I run it and it just want to turn off and I don't know why. The rpm rev up down for few seconds and then it shutoff and if I hold the throttle to keep it on 1000 rpm it vibrate....
  22. Replies
    45
    Views
    3,597

    Injectors seized like member say

    Hi,

    Today, I buy the new fuel pump from the dealer and I install it but the engine not work after that I check the spark plug not wet (no gas on it). So, I pull the injectors to local car workshop...
  23. Replies
    45
    Views
    3,597

    I check the fuel pump and it's not working and...

    I check the fuel pump and it's not working and the coil is short :(
  24. Replies
    45
    Views
    3,597

    Here how is my fuel pump screen and fuel tank...

    Here how is my fuel pump screen and fuel tank look like, Now I will check it with 12 v battery after clean it

    http://greenhulk.net/forums/attachment.php?attachmentid=457142&stc=1
    ...
  25. Replies
    45
    Views
    3,597

    I check today the coil all have spark. The...

    I check today the coil all have spark. The problem is fuel pump not prime gasoline to the injectors and now I try to remove the fuel pump to check it
Results 1 to 25 of 104
Page 1 of 5 1 2 3 4