Search

Type: Posts; User: 32DegH2O

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    16
    Views
    1,730

    FS Due to no interest locally or otherwise in the...

    Due to no interest locally or otherwise in the empty hull, I will be removing all the remaining desirable parts and adding them to the used parts list within the next week.
  2. Replies
    6
    Views
    73

    Since it was a rebuild, have you verified the...

    Since it was a rebuild, have you verified the flywheel/timing is correct? Does the CDI appear to be stock?
  3. Replies
    11
    Views
    168

    You need to get the MSX/Octane finger...

    You need to get the MSX/Octane finger throttle...mounts right on...you do need to remove some of the handle bar padding (on a slt/sltx models) due to the the cable going to the front side. I've done...
  4. Replies
    16
    Views
    1,730

    FS TTT

    TTT
  5. Replies
    16
    Views
    1,730

    FS Thanks for the feedback...I appreciate it! Hope...

    Thanks for the feedback...I appreciate it! Hope your parts are working out well...have a great summer!
  6. Watcon also known as Rock County Jet Ski PWC...

    Watcon also known as Rock County Jet Ski PWC Repair. Located in Janesville, WI 53545 They would also probably have some upgraded/aftermarket parts for you.
  7. Replies
    16
    Views
    1,730

    FS Things are selling fast but still a lot of good...

    Things are selling fast but still a lot of good stuff left.
  8. You have the right jet sizes...but your plugs...

    You have the right jet sizes...but your plugs look lean. This could be a result of a dirty carb. When you put the jets back in, make sure you get them in the correct spot.
    ...
  9. Replies
    16
    Views
    1,730

    FS Yes, they are available. If you see an item...

    Yes, they are available. If you see an item listed and it does not have "payment pending" stated after the price, then it is available....thanks!
  10. Replies
    16
    Views
    1,730

    FS Thanks for your purchase!

    Thanks for your purchase!
  11. Replies
    16
    Views
    1,730

    FS Thanks for your purchase!

    Thanks for your purchase!
  12. Do you know if there has been any engine work...

    Do you know if there has been any engine work done to it?...if so, what? Higher compression heads installed? Sometimes modified skis that have had engine work like porting done to the cylinders and...
  13. Yeah hard to say when you just got it so don't...

    Yeah hard to say when you just got it so don't know the history. Hopefully it's just a good carb cleaning but it may be a jetting issue on the low and mid jets...bogging is usually a rich...
  14. Replies
    23
    Views
    1,670

    Understood and I see where you are coming from. I...

    Understood and I see where you are coming from. I was surprised to see the hp up at those rev. numbers but that's a 785 for ya. Loved all the meticulous OCD stuff you did...I'm the same way! I bet...
  15. Please explain further....new(used CDI)? Where...

    Please explain further....new(used CDI)? Where did you get it from? Was it a used stock one or one that was reprogrammed? Your issue could also be related to a timing issue which comes from the...
  16. Replies
    23
    Views
    1,670

    Awesome build! Don't worry about what the top...

    Awesome build! Don't worry about what the top rpms are...get the top end rpms to be around where the engine makes the most horsepower. Hopefully the engine guys you worked with can give you an idea...
  17. Has it always run this way or has it developed...

    Has it always run this way or has it developed over time? Check your plug color...sounds like it could be a jetting issue. When were the carbs cleaned out last?
  18. Replies
    13
    Views
    434

    Sounds like you may need to clean the carbs out...

    Sounds like you may need to clean the carbs out or you have some blown diaphragms in the carbs.
  19. I assume the ignition update kit came with a CDI?...

    I assume the ignition update kit came with a CDI? Where did you get the kit from?
  20. Replies
    6
    Views
    221

    I would agree...as long as the oils meet the...

    I would agree...as long as the oils meet the requirements suggested by the manufacture and are TCW3 and JASO certified, the oils will mix fine. I have yet to see any documented study that shows this...
  21. The first plug I believe is the new one which...

    The first plug I believe is the new one which replaced your fowled plug so probably hasn't run enough to get a color yet. The others look ok.
  22. Replies
    16
    Views
    1,730

    FS Lowered a lot of prices. Good time to freshen up...

    Lowered a lot of prices. Good time to freshen up those aging GPR parts.
  23. 1st question, what was going on that caused you...

    1st question, what was going on that caused you to get an update kit? 2nd, so Martos reprogrammed the CDI for you and gave you a used Stator? I would tend to question those parts but sounds like...
  24. When you say upgraded to late model ignition,...

    When you say upgraded to late model ignition, what parts did you get exactly?...part numbers?
  25. Replies
    9
    Views
    408

    Do all 3 cylinders get warm? If not, you might...

    Do all 3 cylinders get warm? If not, you might just have a fowled plug. Put new spark plugs in and see if it fixes the problem.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4