Search

Type: Posts; User: Oleg Russia

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. It is necessary to measure the resistance on the...

    It is necessary to measure the resistance on the water temperature sensor. He is in front of the waterbox. Or install instead of the sensor 10kOM resistor. Does your dashboard work? If this sensor is...
  2. Replies
    12
    Views
    1,354

    I also use one cylinder 66E and two 66V....

    I also use one cylinder 66E and two 66V. Everything works, the carburetors settings are the same everywhere.
  3. Replies
    8
    Views
    246

    I also had a leakage problem near the hull. On...

    I also had a leakage problem near the hull. On carburetors gp1200r. I added an additional black gasket from the old kit, then there were no leaks.
  4. I already sent the video but apparently you do...

    I already sent the video but apparently you do not want to see it. This is the simplest and most reliable recovery solution.
    It is necessary to make a sleeve on a lathe. The sizes I wrote. And buy...
  5. More like when the piston went bankrupt. Measure...

    More like when the piston went bankrupt. Measure the compression.
  6. Replies
    6
    Views
    151

    The round membrane on the carburetors is...

    The round membrane on the carburetors is stretched. I had this when the membrane is removed from the carburetor, it does not fit into place, it becomes larger. I noticed this if you use last year's...
  7. https://www.youtube.com/watch?v=GxU7bZOsm0M

    https://www.youtube.com/watch?v=GxU7bZOsm0M
  8. Solving the shaft problem. The sleeve is made and...

    Solving the shaft problem. The sleeve is made and change the glands to a different size. All information on the size listed in the description of the video....
  9. Replies
    43
    Views
    6,289

    Solving the shaft problem. The sleeve is made and...

    Solving the shaft problem. The sleeve is made and change the glands to a different size. All information on the size listed in the description of the video....
  10. Or you can leave it and try to adjust the...

    Or you can leave it and try to adjust the rotating needle. Or do on the settings that are on the site. I did this year, drove 10 hours without problems.
  11. Just a pipe? Is the cylinder head original? The...

    Just a pipe? Is the cylinder head original? The second photo needs to be removed from the insert and there will be a needle. Also below is a needle. Need to remove the carburettors and see the...
  12. If you have a riva stage 3, then you need...

    If you have a riva stage 3, then you need additional carburetor settings. Most likely you have large jets installed, if you say that the adjusting screws are clogged. Send a picture of your...
  13. Make a return line on the prescription of the...

    Make a return line on the prescription of the bill, this will protect you from the poor mixture if one of the carburettors does not work. It will even save you if your crankshaft oil seal crashes...
  14. Replies
    15
    Views
    1,099

    [QUOTE = MrMitch; 2960339] Будут ли связанные с...

    [QUOTE = MrMitch; 2960339] Будут ли связанные с этой проблемой максимальные RPM около 5000? [/ QUOTE]
    the wheel goes down, the servo drive disconnects the wire. Servo, when disconnected, there will...
  15. Replies
    15
    Views
    1,099

    Today I installed another servo. The problem is...

    Today I installed another servo. The problem is no more. Now I have knocked out the crankshaft oil seal =) What's your problem.?
  16. Replies
    15
    Views
    1,099

    I know how to do this. The motor was only...

    I know how to do this. The motor was only assembled and passed 4 hours. Even if you disconnect the cable completely, it opens only by 25 percent.
  17. Replies
    15
    Views
    1,099

    It opens a quarter of the required. It should...

    It opens a quarter of the required. It should open 100 percent during the movement and it opens only by 25 percent.That is, it opens quite a bit. During the test, it opens 100 percent.
  18. Replies
    15
    Views
    1,099

    Приветствую вас. Серво от gpr800 открывает...

    Приветствую вас. Серво от gpr800 открывает сервопривод в диапазоне от 4 до 5, из-за этого двигатель имеет большую яму.
  19. Replies
    15
    Views
    1,099

    In the first message, I wrote that the servo...

    In the first message, I wrote that the servo passes the test. Opens and closes when the engine is off.
    But in motion on the water, the servo drive opens only by a quarter
  20. Replies
    15
    Views
    1,099

    Ypvs Gp1200R does not open

    Hello. In 2001 there is Gp1200r. YPVS does not work correctly. The reason is not known. When you start, ypvs makes the test open and closed. During the movement, only 1/4 is opened. Installed servo...
  21. Replies
    5
    Views
    418

    Hi. If there is no water temperature sensor,...

    Hi. If there is no water temperature sensor, there will be no spark.
    The forum discussed this before. If I'm not mistaken in the plug of the sensor installed a resistance of 10 kΩ. And the spark...
  22. Replies
    8
    Views
    644

    [QUOTE = Robb235; 2955177] Кажется, я помню, что...

    [QUOTE = Robb235; 2955177] Кажется, я помню, что у Osidebill была нить или липкая, где-то рецепт настройки карбюратора. У меня есть 95 пилотных самолетов, но они не могут найти рекомендуемые...
  23. Replies
    301
    Views
    167,037

    Sticky: Yamaha gp1200r 66v Hello. Please, help. I bought...

    Yamaha gp1200r 66v
    Hello. Please, help. I bought used carburetors in Japan. He removed the stubs from the needles.
    The high speed is 1 = 1.7\8 2 = 1.1\4 3 = 1.3\4
    Low speed was...
  24. Replies
    11
    Views
    1,743

    Probably they talked about the sensor of exhaust...

    Probably they talked about the sensor of exhaust gas temperature, in return, resistance 1 is put.
  25. Replies
    11
    Views
    1,743

    Measured the resistance of its sensor, 14.3 kΩ

    Measured the resistance of its sensor, 14.3 kΩ
Results 1 to 25 of 27
Page 1 of 2 1 2