Search

Type: Posts; User: casey67

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    71

    Sounds like something in the jet pump- need to...

    Sounds like something in the jet pump- need to remove it.
  2. That is the battery voltage while cranking. The...

    That is the battery voltage while cranking. The voltage supplied to everything while cranking, the CDI really- really needs enough to operate at all.
  3. It is normal for a Virage/Genesis to crank with...

    It is normal for a Virage/Genesis to crank with out the lanyard, it will not start without lanyard.

    10.6 is the minimum voltage while cranking. At or below that it is likely to not have spark.
    I...
  4. You need to keep your conversation in the same...

    You need to keep your conversation in the same thread.Or start a thread.
    Digging up 7 month old threads will cause confusion.

    A bad LR causes the bilge to run constant.
  5. The aftermarket LR-505 have a very attractive...

    The aftermarket LR-505 have a very attractive price but do not work well. We have had a lot of complaints with aftermarket electronics. Until they improve their quality, I recommend a genuine Polaris...
  6. LR-505 is located above the CDI in the elect box....

    LR-505 is located above the CDI in the elect box. Is the CDI aftermarket ? Where did you purchase the ignition parts ?

    Start with testing voltage on red/purple wire while cranking.
  7. Hmm. I would wait for a reply from K447. The...

    Hmm. I would wait for a reply from K447.

    The LR23 yellow circuit controls the charging system (voltage regulator) and is also a 1/2 wave rectifier. I'm not sure what it does to limit voltage ,...
  8. Replies
    77
    Views
    2,600

    The upper body is the same as 98-2001 SL's. Yes...

    The upper body is the same as 98-2001 SL's. Yes the SLX or SLH seat will fit.
  9. Replies
    3
    Views
    529

    FS - Parts PM sent

    PM sent
  10. Replies
    3
    Views
    529

    FS - Parts 2 remaining. I see used shafts sell for $100,...

    2 remaining.

    I see used shafts sell for $100, price goes up in the spring.
  11. Replies
    2
    Views
    447

    The preferred procedure in the service manual is...

    The preferred procedure in the service manual is to turn idle screw till you can get 1/8 inch drill bit shank snuggly between first throttle plate and carb body.
    Then adjust #2 carb and #3 carb the...
  12. As K447 stated- start with a strong/new battery....

    As K447 stated- start with a strong/new battery. A bad battery will draw down a jumper.

    Start with the basics. Is there a tether under the stop switch ?
    Is the fuel switch turned to reserve ? ...
  13. There are 2 rubber o-rings on the end of the...

    There are 2 rubber o-rings on the end of the starter. I am guessing they are stuck, prying and twisting is all you can do.
  14. Replies
    27
    Views
    679

    Nothing that uses a MFD uses an ECU. The temp...

    Nothing that uses a MFD uses an ECU.
    The temp switch simply sends a signal when hot. The ski does not rely on the switch for anything under normal conditions.
  15. Replies
    4
    Views
    300

    Measure directly at the CDI ( red/pur and blk )...

    Measure directly at the CDI ( red/pur and blk ) Does red/pur go directly to red/pur ? Disconnect blk/yel.
    What you describe sounds like low voltage.
  16. Replies
    27
    Views
    679

    Polaris Temp switch is exactly that, on or off.

    Polaris Temp switch is exactly that, on or off.
  17. Replies
    4
    Views
    300

    How and where did you measure the 11.6 ?

    How and where did you measure the 11.6 ?
  18. Replies
    3
    Views
    529

    FS - Parts New PRO 1200 driveshaft 6230204/6230197

    Selling a new Polaris drive shaft that only fits the 2000 and 2001 PRO 1200.
    Polaris part # 6230204. It replaces # 6230197.
    It is new, unused exactly as sold by Polaris. Does not come with bumpers....
  19. Replies
    3
    Views
    226

    I looked through some of this guys parts list;...

    I looked through some of this guys parts list; 262-347-8509. Mention you are from GreenHulk. Please be reasonable with your requests.
    All prices are + shipping,if any. Tom lives just west of...
  20. Replies
    3
    Views
    226

    I looked through some of this guys parts list;...

    I looked through some of this guys parts list; 262-347-8509. Mention you are from GreenHulk. Please be reasonable with your requests.
    All prices are + shipping,if any. Tom lives just west of...
  21. Replies
    7
    Views
    338

    Sorry,meant to say I would use the 01 CDI from SBT

    Sorry,meant to say I would use the 01 CDI from SBT
  22. Replies
    7
    Views
    338

    What testing have you done to verify all 3 need...

    What testing have you done to verify all 3 need CDI's ? Polaris CDI's do go bad but not that often, to have 1 person with 3 bad would be super astronomical odds.

    There are exhaust differences with...
  23. Replies
    4
    Views
    286

    Read through the 92-98 service manual, it has a...

    Read through the 92-98 service manual, it has a write up for synch for carbs, same layout as the throttle bodies.
  24. Replies
    9
    Views
    227

    Welcome to GreenHulk. Did you do the Ohm test...

    Welcome to GreenHulk.

    Did you do the Ohm test with the 9v battery and turning the engine ?
  25. Replies
    5
    Views
    406

    The accel pump is bolted to the front carb but...

    The accel pump is bolted to the front carb but has hoses that feed all three carbs. Blow carb cleaner through the one-way brass fittings at the carbs.

    When I did the carbs on my 97 SL1050 I went...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4