Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.07 seconds; generated 48 minute(s) ago.

  1. Replies
    2
    Views
    115

    When it started getting good.....

    2003, Seadoo released the GTX Limited Supercharged with 185hp!!! A customer of mine just bought these matching twins from an older fellow. They need a good detailing as they've been sitting unused...
  2. Replies
    11
    Views
    480

    Bad news bubba.....the rear shaft bearing seized...

    Bad news bubba.....the rear shaft bearing seized up and snapped that shaft. Also looks like it ruined the SC housing. You'll need to pull the engine so you can remove the PTO housing and find the...
  3. Just do like all my customers and don't maintain...

    Just do like all my customers and don't maintain anything 'til it breaks, lol!!
  4. Replies
    18
    Views
    830

    The one directly under the air compressor returns...

    The one directly under the air compressor returns to the oil tank. You'll probably need to clean the oil out of all the RAVE tubing too........and don't forget to hook that up BEFORE the engine is...
  5. I get 'em in stock at the local auto parts house....

    I get 'em in stock at the local auto parts house. I'll check up on the part number.
  6. Thread: 2002 1100 Di

    by Myself
    Replies
    9
    Views
    199

    Have you verified TPS voltage is smooth with no...

    Have you verified TPS voltage is smooth with no dead spots while slowly moving throttle?
  7. Replies
    18
    Views
    830

    Yes, pointed straight up. look for a tee at the...

    Yes, pointed straight up. look for a tee at the RAVE solenoid. Line with check valve goes to that. It's just a vent.
  8. Replies
    4
    Views
    342

    If the ECU is from an '05 215 then it should work.

    If the ECU is from an '05 215 then it should work.
  9. Replies
    18
    Views
    830

    Brass nipple......there is a vent line with a...

    Brass nipple......there is a vent line with a check valve going to a T right by the RAVE solenoid.
  10. Replies
    9
    Views
    202

    If they're not tweaked too bad I just bend 'em...

    If they're not tweaked too bad I just bend 'em back cold with a Cresent wrench.
  11. Replies
    17
    Views
    1,799

    I believe it's a 1/4" socket and I hammered it a...

    I believe it's a 1/4" socket and I hammered it a bit to 'egg' it. Fits on most oil pumps. Just used it on a Seadoo 951 Di the other night.
  12. Thread: Yamaha remote

    by Myself
    Replies
    3
    Views
    142

    Don't have one for our FXHO Cruiser and never...

    Don't have one for our FXHO Cruiser and never did......though we've not put that many hours on it either.
  13. Replies
    9
    Views
    202

    Run it. Yamaha acceptable clearances are...

    Run it. Yamaha acceptable clearances are .008-.024.
  14. Replies
    2
    Views
    199

    Normally it's because when the engine blew up...

    Normally it's because when the engine blew up some metal bits get smashed in between the oil pump gears and mess them up. I've used many WSM oil pumps for the 4tecs and never had any issues. There...
  15. Replies
    11
    Views
    280

    I pull 'em out of every one I work on. Idle it...

    I pull 'em out of every one I work on. Idle it around a solid 5 minutes, then ride easy another 5 minutes......good to go. Unless your riding 50* water, then add a restrictor or ball valve. Many...
  16. Here's an Ultra 150 manual. Same thing, different...

    Here's an Ultra 150 manual. Same thing, different hull.--->http://www.mediafire.com/file/inwydzcz2jm/Kawasaki_Service_Manual_Ultra-150.pdf/file
  17. I just got an FXHO started the other day that...

    I just got an FXHO started the other day that only had compression in one cylinder.....I mean NOTHING on the other 3. A guy bought it at a sale and it had sat for 2 years. The ends of all the spark...
  18. Replies
    3
    Views
    138

    Like new again!

    Like new again!
  19. Replies
    6
    Views
    218

    The stator needs tested while on the ski. These...

    The stator needs tested while on the ski. These things can ohm out perfect but not create enough voltage to power the ignition properly. I normally find an issue by testing AC output voltage of the...
  20. Time for some custom paint and airbrush work!

    Time for some custom paint and airbrush work!
  21. And read the little tweets in the article. I'm...

    And read the little tweets in the article. I'm sorry but surely nobody on this planet is that stupid..........April fools!
  22. Replies
    9
    Views
    169

    Some interesting info here.

    Some interesting info here.
  23. Replies
    6
    Views
    218

    If it's aftermarket and not OEM Kawasaki then I...

    If it's aftermarket and not OEM Kawasaki then I would be skeptical of it.
  24. Yep.....what those guys said. Also if it wasn't...

    Yep.....what those guys said. Also if it wasn't done properly with engine completely disassembled, there's a good chance something is already screwed depending on how long it was ridden this way.
  25. Replies
    6
    Views
    218

    AFTER you make sure you have matching components,...

    AFTER you make sure you have matching components, test the stator.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4