Search

Type: Posts; User: gianniadorno

Search: Search took 0.00 seconds.

  1. Seadoo Oil Pressure Switch Connector and pins

    Can’t seem to find any sort of part number for more importantly the pins but also the housing for the ops connector.
  2. Replies
    5
    Views
    370

    Cm tech is a fiberglass core with an acrylic...

    Cm tech is a fiberglass core with an acrylic outer layer instead of gelocat so all the epoxy resin repairs apply and the outer skin is to be painted according to seadoo. Not sure where you’d find the...
  3. Replies
    23
    Views
    911

    The end cap on my ski broke once and it took on...

    The end cap on my ski broke once and it took on water as well. It also lost power because the driveshaft splines weren’t fully engaged as they were slid forward and it grinned the driveshaft into a...
  4. Replies
    5
    Views
    370

    Its a fiberglass hull so you can repair it with...

    Its a fiberglass hull so you can repair it with marine epoxy or resin. Depending on how big the hole is you might want to lay in some fiberglass to strengthen the patch but as long as it isnt too big...
  5. Replies
    23
    Views
    911

    Yes, your engine should be fine. This actually...

    Yes, your engine should be fine. This actually makes more sense with the choppy water too because they like to shift alignment when they come down too hard.
  6. Replies
    23
    Views
    911

    The impeller likely came off because of the...

    The impeller likely came off because of the driveshaft being at the angle stated in the previous post. This might cause it to bind in the pump itself, inducing enough force on the sides to spin it...
  7. Replies
    23
    Views
    911

    The best way I can explain this is as follows....

    The best way I can explain this is as follows. The engine has likely shifted a couple degrees maybe five for examples sake clockwise. Now imagine the shaft that needs to go straight into the engine....
  8. Replies
    23
    Views
    911

    The thrust bearing is likely ok. The damage...

    The thrust bearing is likely ok. The damage described sounds like engine misalignment. I would take it to seadoo and point out to them in person that that piece of rubber coming off of the engine...
  9. Replies
    23
    Views
    911

    If the engine is misaligned it can cause the...

    If the engine is misaligned it can cause the carbon seal to not seat completely flush with the carrier ring (metal piece that sits on top). When these two pieces aren't perfectly flush, there is a...
  10. Replies
    23
    Views
    911

    It might be a longshot but it even appears you...

    It might be a longshot but it even appears you can see misalignment in the photo you sent if you look at the distance at the points in the picture are different meaning its possible the engine might...
  11. Replies
    23
    Views
    911

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=461881&stc=1The broken piece in the picture is just the rubber bellows. It is meant to shield the driveshaft from everything else in the engine...
  12. Replies
    23
    Views
    911

    I would think that you would need an engine...

    I would think that you would need an engine alignment if you had cracked a carbon seal. Were there signs that the driveshaft was touching the inner edges of the carbon seal, like scoring on the...
  13. Replies
    23
    Views
    911

    What do you mean when you say the impeller came...

    What do you mean when you say the impeller came off? The whole pump housing came off?
  14. Not anything i'm aware of other than the shop...

    Not anything i'm aware of other than the shop telling me that I had a bad motor mount. I don't go to that shop anymore after it sank and he had "fixed it".
  15. 2003 GTX SC Keeps losing engine alignment and filling with water

    My 2003 GTX SC went to a shop a very long time ago because it sank on me. Shop replaced motor mount and claimed to have aligned it. Right after getting the ski out again, it began to fill with water...
  16. Replies
    2
    Views
    250

    I started looking up pictures of different places...

    I started looking up pictures of different places inside the engine and the plastic cover on the camshaft gear was missing. After looking at the destroyed piece, it looks just like the cover. Now I...
  17. Replies
    2
    Views
    250

    Unknown plastic in 4tec engine

    I was recently tearing down my 4tec 215, and when I was taking off the valve cover I noticed there was some chewed up plastic that appears to have ran straight through the timing chain and sprocket....
  18. Replies
    29
    Views
    2,977

    How did you copy the original ski without getting...

    How did you copy the original ski without getting the epoxy stuck to the seadoo gel-coat. I'm trying this out on my own but I'm not sure if normal fiberglass release wax will be enough for the...
Results 1 to 18 of 18