Search

Type: Posts; User: turboman412

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    139

    Those oem clips are junk, what type of line did...

    Those oem clips are junk, what type of line did he use? The poly line i use forms to the nipple and is hard to come off with no clamp.
  2. Have you checked your tank? Ultra leaks all over...

    Have you checked your tank? Ultra leaks all over on every one i have ever seen from sending unit. Just make sure top pf your tank is dry
  3. If back at all....

    If back at all....
  4. Replies
    11
    Views
    139

    I have pwc engines rebuild my cranks and he does...

    I have pwc engines rebuild my cranks and he does an excellent job, currently have 4 of them and two in higher hour stxr and ultra. Maybe give him a call and pick his brain on sending engine there
  5. I wouldnt send anything to skiworx fyi do a...

    I wouldnt send anything to skiworx fyi do a search not a good idea
  6. http://greenhulk.net/forums/showthread.php?t=49594...

    http://greenhulk.net/forums/showthread.php?t=49594

    This thread is all info you need, drop john a pm if you have any questions
  7. Mine are around 130-140. Every stock rebuild i...

    Mine are around 130-140. Every stock rebuild i have done normally around 115-120. Your elevation could be what the difference is. The engine i have on the bench i will compression test once in the...
  8. Youll have to ask ada i am not sure if in safe...

    Youll have to ask ada i am not sure if in safe range.

    Run the stock pisser, running on hose all depends on pressure at your house.

    I cut the lip off the side of drive shaft cover and moved...
  9. Replies
    22
    Views
    364

    All depends on your budget, i purchased mine when...

    All depends on your budget, i purchased mine when rhass was not available. Planning on doing my mounts and thru hull next year or so which i will be using rhaas
  10. Replies
    10
    Views
    223

    No its perfectly fine for it to sit in carbs

    No its perfectly fine for it to sit in carbs
  11. Replies
    22
    Views
    364

    Can always run a wsm one if you dont wanna drop...

    Can always run a wsm one if you dont wanna drop the rhaas
  12. Replies
    22
    Views
    364

    I wouldnt chance it, have had a ski almost sink...

    I wouldnt chance it, have had a ski almost sink from a bad holder
  13. Replies
    10
    Views
    219

    The way the stinger is modded it has no effect on...

    The way the stinger is modded it has no effect on cooling cylinders and pipe. It only cools the water box at this point, if you have no flow to water box you melt hoses.
  14. Replies
    2
    Views
    137

    2002 stxr? Its the 14 gallon tank design only...

    2002 stxr? Its the 14 gallon tank design only thing you can do is put nose of trailer in air or upgrade to the 16 gallon tank which is redesigned to fill full when flat
  15. Replies
    10
    Views
    219

    Stinger valve will not cause an over heat/limp...

    Stinger valve will not cause an over heat/limp mode.. only if the stinger gasket was installed incorrectly, the pipe would be very hot but cylinders cool

    I would run the ski and see where its cool...
  16. Your good, enjoy the ski now

    Your good, enjoy the ski now
  17. Enjoy, green is old ethonal make sure you treat...

    Enjoy, green is old ethonal make sure you treat the tank every run...
  18. Replies
    10
    Views
    219

    Have you felt the pipe where sensor is? Is it...

    Have you felt the pipe where sensor is? Is it hot? Should be as cool as the cylinders. Have had trouble with bad sensors in the pass throwing a false over heat in the past.
  19. Seafoam does wonders.

    Seafoam does wonders.
  20. Replies
    6
    Views
    156

    WTB - Parts Theres not enough material to achieve that

    Theres not enough material to achieve that
  21. Theres a rubber oring which is what is stuck,...

    Theres a rubber oring which is what is stuck, wd40 and vice grips...
  22. The vent lets air into the tank not out

    The vent lets air into the tank not out
  23. Alot of pressure is normal Pull the needle...

    Alot of pressure is normal

    Pull the needle seats, theres screens behind them make sure not clogged
  24. Your lean, pull your carbs and go through

    Your lean, pull your carbs and go through
  25. Ah ok, must of missed that and for some reason...

    Ah ok, must of missed that and for some reason thought we were talking about an 1100.

    Mine gps runs consistently 63mph, i have not gps since the addition of a shred master.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4