Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    4
    Views
    284

    I have 2 on my bench now. If I remember I will...

    I have 2 on my bench now. If I remember I will post my measurements up tomorrow.

    Sean
  2. Have yall had issues with the caps cracking near...

    Have yall had issues with the caps cracking near the threads where the hose/spout threads in? My caps all seem to die on the seam there even if I don't tighten them all that much. I have been...
  3. FS - Parts Bump Sean

    Bump

    Sean
  4. Replies
    5
    Views
    170

    Slide it on until it stops. Make sure you have...

    Slide it on until it stops. Make sure you have the rings fully seated, wrap them with a thin layer of paper tape or painters tape just enough to hold the rings in place. The factory just intalls a...
  5. Replies
    9
    Views
    345

    Thats great, thanks for posting it. Sean

    Thats great, thanks for posting it.

    Sean
  6. Replies
    77
    Views
    2,634

    Made a fixture plate to bore the kawasaki...

    Made a fixture plate to bore the kawasaki driveshaft thru hull out to fit the doo driveshaft and carbon seal carrier.

    Swag offroad tube notcher shaft(1" Version)
    3/8 Milwaukee hole saw arbor
    ...
  7. Replies
    11
    Views
    411

    I agree, the coupler is probably too close. The...

    I agree, the coupler is probably too close. The rear output shaft bearing is a pretty tight fit to the output stub shaft iirc and has the rear motor mounts cast into it.

    I have one our now of you...
  8. Replies
    2
    Views
    515

    That's cute. I have 2 like this that are probably...

    That's cute. I have 2 like this that are probably going go cost me more than they are worth to get back to good. If they hadn't been free I would have said no.

    Sean456042
  9. FS - Parts Kawasaki 4 stroke parts, pistons, cams, pumps, props.

    1 set of forged mtc pistons, stock compression ratio

    3 oem stx 15f pistons

    4 oem ultra 250 pistons

    1 modified ultra 250 155mm exit nozzle bored for nozzle rings 83mm, 84mm and 85mm rings.
    ...
  10. I was going to suggest using marine tex on the...

    I was going to suggest using marine tex on the small chunk but then I saw the keel. It my need to get flipped and re-gelkoted.

    Sean
  11. Replies
    3
    Views
    158

    WTB - Parts Pm sent Sean

    Pm sent

    Sean
  12. Replies
    7
    Views
    419

    Check the thread in my signature. If you pull the...

    Check the thread in my signature. If you pull the pumps, don't crank the motor over with the starter. Only rotate the engine by hand.

    If the gauges are bad, I can flash the ecus to 2004 spec to...
  13. Replies
    18
    Views
    616

    You can probably move it forward if you pay...

    You can probably move it forward if you pay attention to the hull while doing so. If you do move it forwards, you will increase the tongue weight so be mindful of that.

    Sean
  14. Replies
    27
    Views
    687

    The one I am messing with is here:...

    The one I am messing with is here: http://greenhulk.net/forums/showthread.php?t=283069

    Sean
  15. Replies
    27
    Views
    687

    Checkout koso, I am playing around with one of...

    Checkout koso, I am playing around with one of their gauges now, seems reasonably well made.

    Sean
  16. Replies
    77
    Views
    2,634

    You are correct, the fitting can either be...

    You are correct, the fitting can either be silicone'd to the bulkhead (as stock does) or you can use the bulkhead washer as the fitting does in other applications.

    One other think I am...
  17. Replies
    77
    Views
    2,634

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=455791&stc=1
    Dimensions are based on aeromotive fittings and 2008 rxt-x steering cable. Kawasaki cables are a little smaller in diameter but...
  18. Replies
    37
    Views
    9,757

    If my memory is correct, when this was brought up...

    If my memory is correct, when this was brought up a few years ago it came down to the seating position being the issue. Basically they claimed it was because you were riding on the pwc vs in a boat...
  19. Last time I looked they were like $120 Sean

    Last time I looked they were like $120

    Sean
  20. Replies
    77
    Views
    2,634

    I may have figured out a way to make control...

    I may have figured out a way to make control cable thru hull fittings for relatively little money.

    Start with a -10an bulkhead fitting and hard line nut.

    Drill the an fitting through with a...
  21. You can drill and tap the cover for a 1/8npt to...

    You can drill and tap the cover for a 1/8npt to hose fitting adapter but it will restrict the flow a bit. I looked into fabricating a replacement cover with 1/4npt threads but it was going to be too...
  22. Thanks for the reply. I got new oem seals in the...

    Thanks for the reply. I got new oem seals in the mail a few days ago but I am waiting on the tool to pull the coupler now. The bearings all feel good as do the connecting rods this was more for peace...
  23. Cool pictures, I am hoping to explore Buchanan at...

    Cool pictures, I am hoping to explore Buchanan at some point. Havasu also has some incredible views if you get out in that area.

    Sean
  24. Replies
    77
    Views
    2,634

    I gave a lot of thought to going that route for a...

    I gave a lot of thought to going that route for a number of reasons but ultimately for me the simpler way was to just use the doo setup as is. I am not thrilled about having the carbon seal setup but...
  25. Replies
    20
    Views
    1,281

    Are you talking about the older model STX1100?...

    Are you talking about the older model STX1100? Can you post a picture of the rideplate mod?

    Sean
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4