Search

Type: Posts; User: Zulu989

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. My question was which jet to use. I figured it...

    My question was which jet to use. I figured it out that a main jet is a technical term for a high speed jet and a pilot jet is a low speed jet. For those that didn’t know including my self. So a high...
  2. Anyone know if it’s the low speed jet that gets...

    Anyone know if it’s the low speed jet that gets used in the RIVA fuel line restrictor barb fitting? I can’t tell where it specifies that but it would seem so since many say just use the stock 90...
  3. Update for engine leak down test- holding 6psi...

    Update for engine leak down test- holding 6psi for over 20 mins with no signs of dropping. Please see picture and let me know if it’s an acceptable way of doing it....
  4. Update for compression test: 126 in both...

    Update for compression test: 126 in both cylinders. Just bought 2” plugs. They fit in the aluminum plate on the intake Incase anyone was wondering which size was required for the leak down test.
  5. Anyone know what size plugs to seal off the...

    Anyone know what size plugs to seal off the exhaust and intake for the leak down. I plan on removing the stinger and sticking a plug in the exhaust pipe end that couples to the stinger. Like like 4-5...
  6. Nope. That check valve is to let air in only. The...

    Nope. That check valve is to let air in only. The valve itself points towards the tank There’s multiple threads about how it needs to pressurize. The vent line also has a water separater in the front...
  7. ok I will remove the flapper. I am going to pull...

    ok I will remove the flapper. I am going to pull the carbs again and do the razor blade check. Just the last couple days I have learnt a lot of new things and one of them was the check valve clear...
  8. Maybe u are talking about the flapper on the...

    Maybe u are talking about the flapper on the bottom of the pickup but that is fine too. Anyway just need to know how to test the leads as I believe this is how it’s supposed to be done but I get...
  9. flapper on the tank?? Not sure what u referred to...

    flapper on the tank?? Not sure what u referred to here but I mentioned that the check valve on the tank was good and that I then found out the gas cap seal was bad. Not so bad to follow. It’s all the...
  10. http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=479073&stc=1I get nothing so I can’t be doing it right
  11. I tried to test the wires but couldn’t figure out...

    I tried to test the wires but couldn’t figure out how. I have a second set but one boot is missing and I would have to get a boot repair. I just started it now and the rev will hang a bit but if I...
  12. Ok gas tank is sealed. I put air in it and could...

    Ok gas tank is sealed. I put air in it and could actually see the tank expand and hold.
  13. Guess I still have lots of learning to do with...

    Guess I still have lots of learning to do with this machine. I had two things going against me while testing in the water yesterday. 1 was the fuel cap and the other was the fact that I was trying to...
  14. Yes I said before it was working. Here is the gas...

    Yes I said before it was working. Here is the gas cap. :facepalm:http://greenhulk.net/forums/attachment.php?attachmentid=479044&stc=1
  15. Watching videos by shade tree jetski and...

    Watching videos by shade tree jetski and apparently the fuel cap is not supposed to leak. I noticed it leaking when I was trying to push fuel into the carbs. Maybe that’s why I’m not getting enough...
  16. It’s working as it should

    It’s working as it should
  17. I’m going to see if the 1 way valve going Into...

    I’m going to see if the 1 way valve going Into the tank is blocked and causing fuel starvation
  18. Put it on the water and with the stock screw...

    Put it on the water and with the stock screw settings, it just bogged to hell. Keep in mind when I put the new base gasket on last night I decided to put the 92.5 jet in and the 1.5 n/s. I richened...
  19. It just takes a few seconds for the throttle to...

    It just takes a few seconds for the throttle to die down. Doesn’t run away.
  20. So I got it started pretty quick using the choke....

    So I got it started pretty quick using the choke. Still a slight air leak but more controlled. I was able to rev it up and witness the power valves opening so we may have some luck here. Note to all...
  21. View Post

    Yea thatís what I used
  22. I took it all apart and put grease where I could....

    I took it all apart and put grease where I could. Made a new base gasket. It’s all back together now. Will try it in the morning.
  23. Took off the carb and found the carb plate to...

    Took off the carb and found the carb plate to engine main gasket was the wrong way. It was upside down. Swapped it over but it’s too late I guess. Now I have a major Air leak. Now I need a new gasket...
  24. Got a question about the little washers that come...

    Got a question about the little washers that come with the Mikuni kits for the pilot screws. They are much smaller than the originals and are the same for the low and high speed screws even though...
  25. Seems like Iike something is going on. Will...

    Seems like Iike something is going on. Will investigate tonight. I got it in the water and go to take off and in about 2-3 seconds or about 16mph it looses all power and bogs for a second and then...
Results 1 to 25 of 71
Page 1 of 3 1 2 3