Search

Page 1 of 11 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    17
    Views
    516

    The engine is basically the same as...

    The engine is basically the same as this....https://youtu.be/dL3My_Iw8Wc
  2. The campgrounds are closed in northern Arkansas...

    The campgrounds are closed in northern Arkansas but the ramps are still open and they've waived fishing licenses too. Anybody can fish. I'm still getting calls and have had 5 skis brought in for...
  3. Replies
    17
    Views
    516

    Ya, I'm still thinking it sounds like a loose...

    Ya, I'm still thinking it sounds like a loose valve tick.
  4. Thread: Opinion needed

    by Myself
    Replies
    13
    Views
    317

    How much is it? If it's 2k then go for it. If...

    How much is it? If it's 2k then go for it. If it's $3500 then NO.
  5. Replies
    17
    Views
    516

    Put the cover back on. Start it up and hold a...

    Put the cover back on. Start it up and hold a dowel rod or piece of PVC pipe to your ear. Touch the pipe to the engine in various places to see where it's the loudest.
  6. Thread: Tired SUV

    by Myself
    Replies
    5
    Views
    201

    Well, that's a 65u engine which is pretty...

    Well, that's a 65u engine which is pretty reliable. For most of the older 2-stroke machines 200-250 hours and they're ready for a top end. You will need to bore the cylinders and go with new oversize...
  7. Was the water cool or warm in the hull?

    Was the water cool or warm in the hull?
  8. Replies
    8
    Views
    820

    Is it an SBT crank?? They use crap bearings and...

    Is it an SBT crank?? They use crap bearings and seals. As stated either just valve it off or do a rotary gear oil loop and fill it with thick gear lube leaving the injection part alone. That's what...
  9. Replies
    30
    Views
    1,587

    Ha.....actually I set a 1/4' drive ratchet...

    Ha.....actually I set a 1/4' drive ratchet extension in the hole and put the tip of the dial indicator down in the end of the extension. good enough to watch the dial move!!
  10. Replies
    2
    Views
    342

    If it's no longer available from Yamaha you'll...

    If it's no longer available from Yamaha you'll need to have one made. Any graphics shop should be able to use a high quality pic of the opposite side, flip it in the software, and print one out for...
  11. Replies
    10
    Views
    1,621

    Anything boosted will NOT run right with a non...

    Anything boosted will NOT run right with a non boost ecu. The computer cannot compensate. Maybe he's done spending money cause he bought the wrong ecu.......you'll never get the truth about that lol!
  12. Replies
    20
    Views
    964

    Yes! That is a known issue and common failure...

    Yes! That is a known issue and common failure mode. Perform the balanced return mod to keep that from happening.
  13. Replies
    9
    Views
    611

    And here is the finished guage reinstalled with a...

    And here is the finished guage reinstalled with a new face decal. I had trouble getting a good pic cause of glare and reflection but it's now plainly legible again. =D>
  14. Mmmm hmmmm..........sunk........just like I...

    Mmmm hmmmm..........sunk........just like I thought.
  15. Replies
    7
    Views
    555

    Not on that engine.

    Not on that engine.
  16. I'd go check it out. The lower compression in one...

    I'd go check it out. The lower compression in one cylinder doesn't bother me that bad.....I see it all the time. Betting after a short ride it comes up. It amazes me that so many people don't know...
  17. Replies
    3
    Views
    330

    Are the gauges hooked up? As soon as you crank it...

    Are the gauges hooked up? As soon as you crank it over the gauges should power up and stay on for a minute or so.
  18. Replies
    7
    Views
    554

    The impeller. I have both here I'll try to get...

    The impeller. I have both here I'll try to get you a pic.
  19. Replies
    7
    Views
    554

    No, it's how the pump shaft goes into the...

    No, it's how the pump shaft goes into the impeller.
  20. Thread: Cylinder Crack

    by Myself
    Replies
    15
    Views
    930

    When the engine gets hot that crack is expanding...

    When the engine gets hot that crack is expanding and allowing water to flow through into the port. Replace it.
  21. Thread: Yamaha FX HO

    by Myself
    Replies
    1
    Views
    206

    Well, the trailer and a few parts are worth $500....

    Well, the trailer and a few parts are worth $500. Can't lose! I just finished piecing one together on the cheap. So far, so good but we've only put 2.3 hours on it. Look in the build section for...
  22. Replies
    9
    Views
    375

    Wait a minute...........you have a 10mm wrench...

    Wait a minute...........you have a 10mm wrench you can actually find??!??
  23. Replies
    32
    Views
    3,829

    Got all the cooling and electrical hooked up...

    Got all the cooling and electrical hooked up yesterday. Also made my own free flow exhaust with a couple pvc street 90's as I found in another thread. Filled with oil, put in new plugs, and a hot...
  24. Replies
    32
    Views
    3,829

    Ok, so I figured this exhaust out. First, MAKE...

    Ok, so I figured this exhaust out. First, MAKE SURE the thermoswitch and engine temp switches are installed in the block on the exhaust side. Otherwise they are ALMOST impossible to get to.......ask...
  25. Replies
    5
    Views
    221

    Could very well be the midshaft bearings since...

    Could very well be the midshaft bearings since nobody seems to know about greasing them.
Results 1 to 25 of 251
Page 1 of 11 1 2 3 4