Search

Type: Posts; User: 97gp1200rider

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    2,692

    Any improvements

    Any improvements
  2. Replies
    12
    Views
    2,582

    It could be a slight air leak id leak test frist...

    It could be a slight air leak id leak test frist before u start messing with the carbs again
  3. Replies
    10
    Views
    726

    Compression was good in all cylinders and tools...

    Compression was good in all cylinders and tools it out yesterday and ran great
  4. Replies
    10
    Views
    726

    Lol just need to know

    Lol just need to know
  5. Replies
    10
    Views
    726

    Anyone else

    Anyone else
  6. Replies
    10
    Views
    726

    I'm scared that I messed it up

    I'm scared that I messed it up
  7. Replies
    10
    Views
    726

    It actually ran fine idk so u not think any...

    It actually ran fine idk so u not think any damage was done
  8. Replies
    10
    Views
    726

    Gp1200 need help asap

    Hey guys just went out for a 30min ride and when I got back home started to wash ski I opened up the engine capartment and realized only one spark plug boot was on bc I forgot to put the other two...
  9. Replies
    2
    Views
    457

    Found out there 37cc

    Found out there 37cc
  10. Replies
    2
    Views
    457

    R&D head on gp1200

    Hey guys getting R&D head used off eBay was wondering if I should change the jetting on carb the domes are marked 7" any ideas on cc and what octane should I run
  11. FS - Parts Do any of them fit gp1200

    Do any of them fit gp1200
  12. Replies
    16
    Views
    2,692

    http://www.greenhulk.net/forums/showthread.php?t=1...

    http://www.greenhulk.net/forums/showthread.php?t=177671&highlight=Balanced+return+mod
  13. Replies
    16
    Views
    2,692

    You shouldnt jet carbs unless you increase or...

    You shouldnt jet carbs unless you increase or decrease air flow in or out other wise you will run too rich
  14. Replies
    16
    Views
    1,285

    ?

    ?
  15. Replies
    11
    Views
    1,372

    ?

    ?
  16. Thread: Top end

    by 97gp1200rider
    Replies
    5
    Views
    632

    Besides flushing

    Besides flushing
  17. Thread: Top end

    by 97gp1200rider
    Replies
    5
    Views
    632

    No I actually am probably milling head for high...

    No I actually am probably milling head for high compression. So does this look normal and is there anything I can do to prevent this
  18. Thread: Top end

    by 97gp1200rider
    Replies
    5
    Views
    632

    Bump

    Bump
  19. Thread: Top end

    by 97gp1200rider
    Replies
    5
    Views
    632

    Anyone?

    Anyone?
  20. Replies
    11
    Views
    1,372

    Ok and for the pics right above should just skim...

    Ok and for the pics right above should just skim the whole area with expoxy then sand
  21. Thread: Top end

    by 97gp1200rider
    Replies
    5
    Views
    632

    Top end

    Hey guys is the outer cylinder walls head and such suppose to look like this and should I just clean it all with a parts cleaner or maybe brake cleaner I work on car and truck motor not really...
  22. Replies
    11
    Views
    1,372

    And for paint will automotive paint in a spray...

    And for paint will automotive paint in a spray can work
  23. Replies
    11
    Views
    1,372

    Idk it's on the the right side of bottom but also...

    Idk it's on the the right side of bottom but also wanna fix middle section of bottom in these pics
  24. Replies
    11
    Views
    1,372

    I don't think just expoxy will do it, the frist...

    I don't think just expoxy will do it, the frist pic the gouge is pretty deep the other isn't though
  25. Replies
    11
    Views
    1,372

    I heard marine Tex is for gel coat what about the...

    I heard marine Tex is for gel coat what about the west systems kit and should I put some pieces of fiberglass in
Results 1 to 25 of 37
Page 1 of 2 1 2