Search

Type: Posts; User: Saum700p

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    14
    Views
    653

    Dean's has a service to taper yours to 160mm. I...

    Dean's has a service to taper yours to 160mm. I don't recall exactly how much but it was reasonable, I had mine done ant it looks great.
  2. Replies
    3
    Views
    188

    wr is the shaft spline holding tool

    wr is the shaft spline holding tool
  3. I have used that hole for the water line. It...

    I have used that hole for the water line. It works but for the 1/2" fitting you need to put washers on it and seal it with 4200/5200. I later changed over to braided line due to blowing the lines...
  4. That 11/15 is way too high rpm impeller I was...

    That 11/15 is way too high rpm impeller I was on the limiter at 8,500 at 65mph with that. You want to look in the area of 13/18. The impeller for the older sho motor have had good results.
  5. Thread: Gp1800r issue

    by Saum700p
    Replies
    15
    Views
    1,144

    Going to need a clutch and they are on backorder...

    Going to need a clutch and they are on backorder right now. There are options to rebuild them but new is preferable.
  6. Replies
    12
    Views
    1,045

    Just call or email them and schedule it. They...

    Just call or email them and schedule it. They have a good turn around on reflash. its only a few 10mm bolts to remove and I usually see turnaround from them in a week.
  7. I can vouch... I got walked at a 20 mph roll on

    I can vouch... I got walked at a 20 mph roll on
  8. Impressive. How much would you have to spend to...

    Impressive. How much would you have to spend to run 80 on a seadoo. Can't wait to see that build. Air filter, and tune crossing the 80 mark should be the best money ever spent on ski mods. Have the...
  9. Replies
    18
    Views
    2,375

    What kinda price are we looking at on these? ...

    What kinda price are we looking at on these? Somewhere around the price of the previous factory clutch?
  10. Following... Great start video Greg. Looking...

    Following... Great start video Greg. Looking forward to seeing the future videos and seeing the new GP out at mudbug in the spring.
  11. Replies
    9
    Views
    994

    They also claimed the new pump last year was a...

    They also claimed the new pump last year was a true 160mm pump.... Hands on determined that to be false.
  12. Replies
    6
    Views
    759

    Timing chain.

    Timing chain.
  13. Replies
    37
    Views
    5,309

    doubtful... i'm full fuel system, tune,...

    doubtful...

    i'm full fuel system, tune, intake, exhaust, fizzle, cams, tune, impeller, nozzle work at 90....
  14. Replies
    6
    Views
    415

    The hoses at the transom forth transom not...

    The hoses at the transom forth transom not sealing, the drive shaft cover, and the intake grate bolts are your most probable causes.
  15. Replies
    8
    Views
    605

    Very happy with my Deans team modified factory...

    Very happy with my Deans team modified factory plate on the vxr and the gp.
  16. Replies
    35
    Views
    3,440

    Best thing to do is get as much data as you can...

    Best thing to do is get as much data as you can speed/rpm, nozzle diameter, etc and call or email Dean. He's a wiz on with these things He dialed my nozzle and pitch in great.
  17. Replies
    35
    Views
    3,440

    Dan If you get a flapper wheel and bore out the...

    Dan If you get a flapper wheel and bore out the nozzle a little at a time you should find a good blend. 82*-83* should be where you want to be, any more you will start loosing top speed as your...
  18. Replies
    9
    Views
    450

    The sinkdoo's have a turn signals...

    The sinkdoo's have a turn signals...
  19. Replies
    6
    Views
    483

    I don't see why the gp and vx seats wouldn't swap...

    I don't see why the gp and vx seats wouldn't swap for the 21's. They are the same redesign. I'll check my dealer the next time i'm over there.
  20. Replies
    2
    Views
    192

    13/19 is the area you want to be in. The 22 will...

    13/19 is the area you want to be in. The 22 will be too steep. Each machine will be it's own along with your climate affecting it. But start with the 19 and test. Give some data then to your mechanic...
  21. Replies
    2
    Views
    194

    Check and make sure they didn't marr the splines...

    Check and make sure they didn't marr the splines on the shaft while holding the shaft on the impeller install. That will cause it to start going in and stop clean out the receiver and apply some...
  22. Replies
    6
    Views
    483

    This generation seat should be able to swap as...

    This generation seat should be able to swap as the last generations were the same on the vx and gp. They are the same dimensions, but sure if you go to a local dealer you could verify this yourself. ...
  23. Replies
    17
    Views
    967

    If you have to fuel up on the water just keep it...

    If you have to fuel up on the water just keep it under 6,000 you'll be fine. As far as boosters just get a quality one and keep some with you. Don't go overkill with it but you can put a little in...
  24. I had that happen on my vxr. I doubt thats your...

    I had that happen on my vxr. I doubt thats your problem because when mine did that it wouldn't start at all. check the wires on the back of your injector plugs. see if any pull out easily. They...
  25. Replies
    21
    Views
    1,711

    Yup... Looks like a dealer installed fogging port.

    Yup... Looks like a dealer installed fogging port.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4