Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    92
    Views
    2,860

    For whatever reason both replacement sets are...

    For whatever reason both replacement sets are marked that way. They are proper for 83mm bore. They are drop in when used with the correct pins and weigh the same as stock. These were used in a 430hp...
  2. Replies
    92
    Views
    2,860

    Mtcs Sean ...

    Mtcs

    Sean
    ...
  3. Replies
    92
    Views
    2,860

    I would make damn sure whatever you get is...

    I would make damn sure whatever you get is waterproof, or can be made waterproof. The newer holly dashes don't look sealed from what I have seen and also don't look sunlight readable since they all...
  4. Replies
    92
    Views
    2,860

    I know a few people running halltechs on ultras...

    I know a few people running halltechs on ultras with good luck. I ran a megasquirt 3 with ms3x specifically for the customization options and the onboard logging. I am also planning on testing a...
  5. Replies
    92
    Views
    2,860

    I have a set of stock 15f compression forged mtcs...

    I have a set of stock 15f compression forged mtcs waiting on you if you want them.

    Sean
  6. Replies
    12
    Views
    537

    What does the piston look like? Sean

    What does the piston look like?

    Sean
  7. Replies
    3
    Views
    117

    FS - Parts No but I am using it for another project. Sean

    No but I am using it for another project.

    Sean
  8. Replies
    12
    Views
    537

    Can you pull the plug and post a picture of the...

    Can you pull the plug and post a picture of the hole from both sides and a picture of the plug?

    Sean
  9. Replies
    3
    Views
    117

    FS - Parts Parts. Ill snap some more later. Sean ...

    Parts. Ill snap some more later.

    Sean

    http://greenhulk.net/forums/attachment.php?attachmentid=468146&stc=1
    http://greenhulk.net/forums/attachment.php?attachmentid=468147&stc=1...
  10. Replies
    0
    Views
    44

    FS - Parts 2004 STX-12f Engine

    I am running out of time/space to finish this before my first kiddo is born so I am going to pass of my garbage you lucky members!

    All prices are part only, shipping will vary and be extra. PP...
  11. Replies
    3
    Views
    117

    FS - Parts STXR Partout

    I am running out of time/space to finish this before my first kiddo is born so I am going to pass of my garbage you lucky members!

    All prices are part only, shipping will vary and be extra. PP...
  12. Replies
    4
    Views
    118

    I had a 12f motor do the same thing. Make sure...

    I had a 12f motor do the same thing. Make sure you change the oil if it smells like fuel. Mine was really bad.

    Sean
  13. Replies
    92
    Views
    2,860

    Huh, hadn't seen that. Interesting. Sean

    Huh, hadn't seen that. Interesting.

    Sean
  14. Replies
    107
    Views
    9,069

    I may try playing with that, if I move it towards...

    I may try playing with that, if I move it towards the tunnel it starts getting really close to the supercharger inlet.

    Sean
  15. Replies
    92
    Views
    2,860

    The taper on these is intentional, once you get...

    The taper on these is intentional, once you get them off you can see it.

    The rods on the 12f are a proprietary rod, I looked into swapping them but they are not the same dims as the bike. I also...
  16. Replies
    104
    Views
    5,173

    Interesting, I have not used that type before. I...

    Interesting, I have not used that type before. I have odi rogues on my bars right now. What did it cost for the doo grips?

    Sean
  17. Replies
    92
    Views
    2,860

    The first 2 are reasonably easy since you can...

    The first 2 are reasonably easy since you can have 2 up and 2 down. The other 2 are more difficult since you have to have all 4 in line. It is really easy to get frustrated and accidentally pop the 2...
  18. Replies
    92
    Views
    2,860

    Doing the top in method on a kawi 4 stroke...

    Doing the top in method on a kawi 4 stroke requires splitting the crankcase though since the lower section has a cast in windage tray. Im going to go that route when my rings show up but thats only...
  19. You should have a little exclamation mark on the...

    You should have a little exclamation mark on the pm that you were sent, click that and it will report the pm. Im on mobile right now so the process may be different.

    Sean
  20. If you have not done so already, please report...

    If you have not done so already, please report the pms so we can ban them. These bots/scammers are a painin the ass and we are trying to get some system in place to stop it.

    Sean
  21. Replies
    92
    Views
    2,860

    I think its a lead in to make installing the...

    I think its a lead in to make installing the rings easier but I could be wrong, its larger than the bore on the bottom.

    If you stick with 12f rods and crank with zx/12f/15f pistons it will be a...
  22. Replies
    92
    Views
    2,860

    The bottom of the bore on the 12f cylinder is...

    The bottom of the bore on the 12f cylinder is tapered (not parallel with the main bore) past the lead in chamfer at the very bottom of the cylinder, the 15f is not.

    I can't comment on its...
  23. Replies
    92
    Views
    2,860

    I should have clarified, when I was talking about...

    I should have clarified, when I was talking about pulling the piston out, I meant out of the non-tapered section. In one of the other posts in this thread, you mentioned running a 15f rod (shorter...
  24. Replies
    107
    Views
    9,069

    Working on my fuel system, trying to adapt the...

    Working on my fuel system, trying to adapt the doo steup to the kawasaki can.

    -3an vent, -6an send, and -6an return.

    I need to fill the stock kawasaki holes and cut a gasket for the plug...
  25. Replies
    92
    Views
    2,860

    The displacement in this case is not the issue,...

    The displacement in this case is not the issue, there are guys making 215hp+ on zx12r motors (they are 1427+ccs so not really a zx12 anymore but still) The issue is everything else on the motor...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4