Search

Page 1 of 7 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    29
    Views
    3,040

    Stainless Steel M6x35, Hex Head, with Anti...

    Stainless Steel M6x35, Hex Head, with Anti seize...
  2. Replies
    56
    Views
    14,124

    How about a 2up +Vtech, then add the MANUAL...

    How about a 2up +Vtech, then add the MANUAL reverse later?
  3. Replies
    41
    Views
    7,010

    If the intake grate is stock, swap it...

    If the intake grate is stock, swap it out...you'll gain 2-3mph easy...

    8200 is too high, you need to adjust the prop...or swap it out.

    Also, remove the Flame Arrestor in the intake manifold...
  4. Replies
    16
    Views
    978

    DADDY! Let me help...

    I can't even cut the grass without my little man wanting to helping...

    Or build a deck...


    337239337240337241


    **The mower was not running during filming...
  5. Thread: whos tuning

    by Danny
    Replies
    11
    Views
    1,023

    From what I can recall, its tough to reflash a...

    From what I can recall, its tough to reflash a 185 ECU. It does not have enough physical memory. You would need an ECU from a 215 to reflash...
  6. Replies
    8
    Views
    1,139

    If you got silver dust, you had a touch down... ...

    If you got silver dust, you had a touch down...

    Is the SC out of the ski? How many hours on the SC?

    The housings can be split with a 1/2 socket, put it between the top spots and turn...there is...
  7. Replies
    25
    Views
    1,672

    .......paid for 8-)

    .......paid for 8-)
  8. Replies
    9
    Views
    1,367

    #1, welcome to the forum... #2, STOP RIGHT...

    #1, welcome to the forum...

    #2, STOP RIGHT THERE...

    Quick lesson...From 2004-2007, the OEM SC's had a fault. They used clutches that are made from ceramic, which when they failed, would send...
  9. Replies
    19
    Views
    2,057

    This is turning into an ODD situation...and it...

    This is turning into an ODD situation...and it must be addressed properly.

    These are a LOT of parts that have gone missing. If any of the them are in the motor, YOU WILL FIND THEM...

    Pull the...
  10. Replies
    19
    Views
    2,057

    If it would have popped while riding, some damage...

    If it would have popped while riding, some damage would have been done. And 60 hours without any issue, even when bouncing around through chop, something would have worked its way towards moving...
  11. Replies
    20
    Views
    1,755

    Get rid of ALL RESIDUE... There are shims...

    Get rid of ALL RESIDUE...

    There are shims behind the shoe, SAVE THEM....

    DRY FIT, DRY FIT, DRY FIT...

    Get the show aligned with the thru hull fitting, not the motor...Center it as perfect as...
  12. Replies
    302
    Views
    26,410

    3-axis CNC mill, with a chunk of metal on the...

    3-axis CNC mill, with a chunk of metal on the table...about a 12x12 chunk, atleast 1/2-5/8 thick...

    You're gonna make a fancy cup holder?
  13. Either rebuild the entire SC, or rebuild the...

    Either rebuild the entire SC, or rebuild the motor....

    Your choice....

    Bearings, bearings, BEARINGS!!!!! Its not the actual bearing itself, its the cages that hold the internals...Heat cycles...
  14. The filter is the FLAME ARRESTOR....by law it has...

    The filter is the FLAME ARRESTOR....by law it has to be in there....

    Just removing it gains you response and boost....about 1psi of boost gain has been reported, and throttle response is vasty...
  15. Didn't you just ask this question in another...

    Didn't you just ask this question in another thread?

    It won't fit if its going into the OEM STOCK LOCATION on the 255 skis...It has to be installed where the resonator is, which has to be removed.
  16. Thread: rxp 7700rpm

    by Danny
    Replies
    6
    Views
    586

    Wear ring is not the issue...its the rubber nose...

    Wear ring is not the issue...its the rubber nose cone that has folded itself backwards!!!
  17. Replies
    11
    Views
    999

    Red SC cases were STANDARD on all SC motors, both...

    Red SC cases were STANDARD on all SC motors, both 185 and 215, for all of 2003 and 2004, with a few early 2005 until they switched to black...

    Until performance outfits like Rude and SeaDoo Centre...
  18. Replies
    4
    Views
    1,734

    FS - Parts You go faster by keeping things light...I would...

    You go faster by keeping things light...I would keep it and clean it up.
  19. Picked up parts today, meeting with the welder...

    Picked up parts today, meeting with the welder HOPEFULLY Thursday night after work, so I can ship it out Friday...

    SAYERS.......I got one extra set for you :)........Do you want it?
  20. Replies
    6
    Views
    736

    Good deal... No matter HOW COLD that water is,...

    Good deal...

    No matter HOW COLD that water is, you are on the water.

    ......I'm reading this thread from work :smt100
  21. Replies
    11
    Views
    999

    Thats a 127mm width, base is a 215 charger...its...

    Thats a 127mm width, base is a 215 charger...its definitely aftermarket...

    The trailing edges look taller...

    My guess...

    - Rotax Racing wheel (looks like mine)
    - Early Riva GenII wheel
    -...
  22. Since every setup is slightly different, I did...

    Since every setup is slightly different, I did not make any lower mounting holes...You must make them yourself.

    You mount everything up, get everything lined up...THEN mark from underneath for the...
  23. Replies
    15
    Views
    1,393

    You had too much oil...

    You had too much oil...
  24. Here is the original thread......

    Here is the original thread...
    http://www.greenhulk.net/forums/showthread.php?t=186929
  25. I'm dropping material off at my waterjetter in...

    I'm dropping material off at my waterjetter in couple of hours. He's going to cut parts right away, I'll try to have it all welded up and in your hands by Friday...I'm making a pair, so if anyone...
Results 1 to 25 of 157
Page 1 of 7 1 2 3 4