Search

Type: Posts; User: Rescue1

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    591

    Yeah the old ones had a steering Hall effect...

    Yeah the old ones had a steering Hall effect sensor that would give it a little throttle via a valve on top of the throttle body. I can assume that the new ones have a similar sensor however the ECU...
  2. Replies
    7
    Views
    591

    Are you turning the handlebars at all while this...

    Are you turning the handlebars at all while this happens? Even a little
  3. Replies
    8
    Views
    358

    Yes the earlier outboards had Ficht, and what a...

    Yes the earlier outboards had Ficht, and what a troublesome setup it was... But wow, I saw the links about about BRP shutting down the outboard manufacturing.. I guess I am surprised and not at the...
  4. Replies
    26
    Views
    1,178

    This may not be the issue but... I've seen plenty...

    This may not be the issue but... I've seen plenty of wires in cars that check correctly with voltage using a DMM or a low current test light.. However if you take a headlight bulb with 2 pigtails...
  5. Replies
    4
    Views
    305

    I know being in Florida you don't know what this...

    I know being in Florida you don't know what this term means(Yes I am jealous) but when I winterize my JetSki I put 1 or 2 of those damp rid containers in the hull and cover it all up. They seem to...
  6. Replies
    8
    Views
    358

    View Post

    Personally I canít stand anything made by BRP. Iím saying this as I rebuild another damned Can Am ATV.

    Anyway, the early ETechs were problematic, the most notable were the FICHT fuel systems,...
  7. I suppose if it helps with those F%^#$@ crappy...

    I suppose if it helps with those F%^#$@ crappy rocker arms they had on the early, and likely still current Pentastar engines it should help with flat tappets.
  8. Replies
    2
    Views
    203

    Rough idle after startup question

    Hello all,

    2012 300X, 150 hours, SCOM and no other mods. I change the exhaust filter every 2 years out of habit as well as the plugs..

    When I go to start the engine after shutting it down while...
  9. Replies
    4
    Views
    304

    I ended up putting all new Gates hose in. Pulled...

    I ended up putting all new Gates hose in. Pulled the intake off, cleaned the injectors as well while there. Everything is back up and running now. Thanks for the advice guys..:smt066
  10. Replies
    8
    Views
    463

    Salt away isn't strong enough to unclog passages...

    Salt away isn't strong enough to unclog passages that are already in the engine. I'm not sure if vinegar works as I've never tried it but most of the ports I've cleaned were manually done, a pain I...
  11. Replies
    7
    Views
    397

    Fluid film is your friend for any brand. The...

    Fluid film is your friend for any brand. The stuff has been proven to be the best corrosion/rust preventer but a test Watercraft superstore did, as well as the "Project Farm" and "South main Auto"...
  12. Replies
    4
    Views
    304

    Thank you sir. Kinda figured but wanted to ask....

    Thank you sir. Kinda figured but wanted to ask. Hopefully this hose holds up better than the OEM stuff. Thankfully I had a bilge pump installed. [emoji51][emoji106]
  13. Replies
    4
    Views
    304

    Water Hose Replacement...

    Hello all,

    I fell victim to the well known crappy hoses Kawasaki put into my 2012 300x with one splitting at the fore oil cooler hose connections. I got some Gates hose in the same size that rated...
  14. Thread: Ultra 300x

    by Rescue1
    Replies
    2
    Views
    280

    Start with the Typical stuff you'd check on any...

    Start with the Typical stuff you'd check on any PWC including but not limited too; Compression test, check the bearings in the pump by at least removing the pump cone. Also check for general neglect...
  15. The Lanox mentioned is a good choice as well as...

    The Lanox mentioned is a good choice as well as Fluid Film. Both are lanolin based products, aka sheep wool fat. But donít use WD40 on anything other than metal because it degrades Rubber. I didnít...
  16. This pretty much sums up my thoughts better than...

    This pretty much sums up my thoughts better than I can explain


    http://www.kawiperformance.com/engine-maintenance-and-longevity-.html
  17. My theory is Kawasaki knew this was an issue and...

    My theory is Kawasaki knew this was an issue and thatís why they redesigned the pistons for the 310. But an unintended consequence or that move was blown pistons which really sucks. Most guys who...
  18. Replies
    21
    Views
    1,116

    PWC Reliability..

    Just seeing what everyone's thoughts are on general PWC reliability. I want to note that this is NOT a brand bashing post at all because ALL past and present manufactures have made idiot and...
  19. Water in the waterbox is fine, just be sure to...

    Water in the waterbox is fine, just be sure to blow it out real good after riding/flushing.

    I like the above mentioned fuel pressure check as the ethanol tends to wreak havoc on the parts.

    The...
  20. Mine does the same thing. My compression and leak...

    Mine does the same thing. My compression and leak down are ok although there gotta be some blow by going into the crankcase causing this. I put a cable tie on it and it's been another 50 hours since...
  21. Also, put a bunch of water in the hull while it's...

    Also, put a bunch of water in the hull while it's on the trailer to see if water leaks from the coupler
  22. Replies
    4
    Views
    382

    I'd back probe the connector for the Knock sensor...

    I'd back probe the connector for the Knock sensor and verify bias voltage coming from the ECU. It should be in the 5volt range.. I'd maybe also do this while riding just to make sure that voltage...
  23. Replies
    18
    Views
    3,876

    In regards to waterproof switches IMO there are...

    In regards to waterproof switches IMO there are only 2 worth buying for PWC's or boats;

    The first is made for industrial applications and you'll see them on CAT equipment and such. They are the...
  24. Replies
    11
    Views
    1,029

    What were your compression numbers as you only...

    What were your compression numbers as you only said they were even.. And I'd also do a leakdown test. Also, I think you hit most of the stuff, look for that thread on there, I think It's in the how...
  25. Filling the hull is a good idea, that's how I...

    Filling the hull is a good idea, that's how I found the leak coming from the bearing housing rubber. Maybe also consider putting a GoPro(or knock off) camera with alight and ride around a bit. I've...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4