Search

Type: Posts; User: mpettapiece

Search: Search took 0.00 seconds.

  1. I just ripped out one and cut the other really...

    I just ripped out one and cut the other really short and looped it to the other fitting like this 450956
  2. Nice looks good!

    Nice looks good!
  3. Replies
    2
    Views
    199

    Thanks got it together now

    Thanks got it together now
  4. Replies
    2
    Views
    199

    Ultra 150 jetpump assembly

    Hi I was wondering if anyone knew if this is the correct spot for the bushing. I was looking at the diagram and it seems like the bushing is supposed to be in the other end...449647
  5. Thanks, how do I pull the fuel rails out?

    Thanks, how do I pull the fuel rails out?
  6. Thanks, I got it off, the impeller shaft snapped...

    Thanks, I got it off, the impeller shaft snapped but didn't break the housing luckily. So I have a new one coming in and will be good to go. Also I decided since I'm waiting anyways I'm gunna rebuild...
  7. I started doing the triple pisser kit for those...

    I started doing the triple pisser kit for those who asked for pictures I got some. It's pretty simple to do, I got the old head fittings out and put the new ones in and stuck the hose on it. It's not...
  8. Yeah we when put a pipe on the breaker bar, it...

    Yeah we when put a pipe on the breaker bar, it started spinning through the vice... Do you know where I could get that tool that turbo man has?
  9. Oh ok I'm using this tool that goes into the old...

    Oh ok I'm using this tool that goes into the old impeller and clamping the small flats on the vice. 449099449100
  10. We are using the spline tool and heating around...

    We are using the spline tool and heating around the impeller
  11. This is what I have set up449094

    This is what I have set up449094
  12. Well my impeller is not coming out any...

    Well my impeller is not coming out any recommendations?
  13. I'm just using life calk silicone

    I'm just using life calk silicone
  14. Yeah for sure, I'm new at this myself but I'll...

    Yeah for sure, I'm new at this myself but I'll keep putting pictures up.
  15. Well got the cone off and getting ready to change...

    Well got the cone off and getting ready to change the bearings and found an inch of water in there...449056449057
  16. Ok thanks!

    Ok thanks!
  17. Ultra 150 Pump Rebuild and Triple pisser

    Hi I was wondering if anyone knows what the best type of greese, oil and lube I need for rebuilding the pump, and also what is the best silicone is for the triple pisser kit. Also if anyone has any...
  18. Replies
    8
    Views
    424

    I was looking at that too, I think my best bet...

    I was looking at that too, I think my best bet would be a shredmaster ride plate and beach house sponsons. Just have to find them they are very rare.
  19. Replies
    8
    Views
    859

    FS Do you have any pictures of the front storage...

    Do you have any pictures of the front storage compartment?
  20. Replies
    8
    Views
    424

    Thanks for the advice Steve! I did buy a bearing...

    Thanks for the advice Steve! I did buy a bearing kit for the pump, I have been researching a few things and I may have to add or remove shims. Is this easy to do myself I dont have much experience...
  21. Replies
    8
    Views
    424

    Looking for mods for the ultra 150

    Hi, I am looking for mods for my ultra 150, I just bought a solaris 16/20 and a triple pisser kit. I was wondering if anyone had a stinger mod, or tdr water box, or something to make it accelerate...
  22. Replies
    2
    Views
    695

    This is awesome! Did you put any mods on it?

    This is awesome! Did you put any mods on it?
Results 1 to 22 of 22