Search

Type: Posts; User: steve45

Page 1 of 8 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    22
    Views
    2,123

    I'm making some progress! I robbed the fuel...

    I'm making some progress!

    I robbed the fuel selector valve from an Ultra 150 to install in the Jet Mate. The original had two valves: On & Off, and On & Reserve. They were in bad shape and...
  2. Replies
    13
    Views
    351

    Yes, you would have to go back to the stock...

    Yes, you would have to go back to the stock stinger, as well as the hoses.
  3. Don't know why this was moved to the Yamaha...

    Don't know why this was moved to the Yamaha section. I saw it in the Kawasaki section and it was moved before I had time to reply.

    This 'Ski does not have an accelerator pump. Since it has a...
  4. Replies
    13
    Views
    351

    No. I did the Triple Pisser Mod, but I also...

    No. I did the Triple Pisser Mod, but I also installed a strainer in the inlet water hose. I bought a couple extra OEM nozzles.
  5. Replies
    2
    Views
    360

    Congratulations! And they changed the color!...

    Congratulations!

    And they changed the color!

    I haven't seen them lift a 'Ski like that before. Guess they deal with boats, too.
  6. Replies
    13
    Views
    351

    Put a small dab of grease on the gaskets to hold...

    Put a small dab of grease on the gaskets to hold them in place.

    You can run the engine on the flush hose at idle and hold the oil pump pulley in the full throttle position and the lines will fill...
  7. Replies
    13
    Views
    351

    Why are the carbs troublesome to replace? If...

    Why are the carbs troublesome to replace?

    If just replacing the oil lines, I probably wouldn't go to the trouble of testing the pop-off valves for the oil lines. However, the carbs have to be...
  8. Replies
    9
    Views
    448

    Somebody here, sorry I can't remember who, had...

    Somebody here, sorry I can't remember who, had one fail under warranty. Kawasaki agreed to pay to install aftermarket pistons, but the owner had to pay for the pistons.
  9. Replies
    20
    Views
    741

    CO2 is NOT a pollutant.

    CO2 is NOT a pollutant.
  10. Bummer!

    Bummer!
  11. Replies
    20
    Views
    741

    This discussion is going off the rails, so to...

    This discussion is going off the rails, so to speak, and should probably be in the Open Discussion section of the Community forums. I decided not to post it after I wrote it last week, but then I...
  12. http://partsfinder.onlinemicrofiche.com/4tec/showm...

    http://partsfinder.onlinemicrofiche.com/4tec/showmodel.asp?type=13&make=kawasakipwc&a=137
  13. Replies
    4
    Views
    169

    I found a piece of tubing that I've used to hold...

    I found a piece of tubing that I've used to hold that coupling together. Send me a PM if you want some.
  14. Replies
    4
    Views
    169

    Buy another pump. There are lots of them on...

    Buy another pump. There are lots of them on Ebay.

    And do a proper fix on that drive coupling. That safety wire could fall off and the coupling will tear up everything. I found a piece of hose...
  15. Replies
    17
    Views
    1,801

    I use a piece of 1/2" ID hose slipped over a 1/2"...

    I use a piece of 1/2" ID hose slipped over a 1/2" OD shank that I place in my drill.

    I think the easiest way to verify proper flow is to mix a tank of pre-mix. Mark the oil tank with a Sharpie,...
  16. There are no air filters, but there should be...

    There are no air filters, but there should be screens. Do not run without the screens or the factory flame arrestor housing. Doing so without carburetor modification will cause it to run lean and...
  17. Thread: Stx di deal

    by steve45
    Replies
    21
    Views
    1,061

    Yes, it sounds like the driveshaft holder is...

    Yes, it sounds like the driveshaft holder is cracked. Take it out and take a good look at it under light. Flex it and you'll probably see cracks in the rubber.
  18. Thread: Stx di deal

    by steve45
    Replies
    21
    Views
    1,061

    Sounds like you need to get a stainless plate...

    Sounds like you need to get a stainless plate made with stainless nuts welded to it. Glue this in from the back side with 5200. Not sure if this is easily possible.

    Worst case scenario, get...
  19. Replies
    2
    Views
    93

    Welcome aboard, ChrHol! I know that there are...

    Welcome aboard, ChrHol!

    I know that there are people here that would trade a good display for that Shredmaster! Most buyers wouldn't have a clue what the Shredmaster is, let alone give you any...
  20. Thread: Stx di deal

    by steve45
    Replies
    21
    Views
    1,061

    Happy Easter to you, Chris! If the leak is...

    Happy Easter to you, Chris!

    If the leak is from the aluminum part that is glued behind the driveshaft seal, yes, you can use 5200. If the driveshaft holder (the black rubber donut) is leaking,...
  21. Welcome aboard, eeeerock! There are some...

    Welcome aboard, eeeerock!

    There are some components that Kawasaki considers to be a permanent part of the hull, and not replaceable. Sadly, this is one of those parts.

    That doesn't mean you...
  22. Do a search about fogging that model. It has a...

    Do a search about fogging that model. It has a different supercharger from the current 310 models. I don't believe it came with a fogging port. I know that owners added fogging ports to some...
  23. Thread: Stx di deal

    by steve45
    Replies
    21
    Views
    1,061

    You can't 'patch' the driveshaft seal. The...

    You can't 'patch' the driveshaft seal. The 'holder' is what Kawasaki calls it. It's just a rubber donut that the bearings and seals sit in. It splits with age and leaks. Normally, you would just...
  24. Thread: Stx di deal

    by steve45
    Replies
    21
    Views
    1,061

    I wouldn't worry about the CPS spec, 1 ohm out of...

    I wouldn't worry about the CPS spec, 1 ohm out of 400 isn't a big deal.

    Good thing you caught the driveshaft seal before you put it back together!

    Don't understand the battery tray rusting...
  25. Thread: Stx di deal

    by steve45
    Replies
    21
    Views
    1,061

    You'll have to test the pop-off valves. They...

    You'll have to test the pop-off valves. They should open at about 4-5 PSI.

    That's not a Kawasaki part. Looks like a lead from a remote start switch or something.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4