Search

Type: Posts; User: speeder

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Sticky: I suggest you edit your original post to remove...

    I suggest you edit your original post to remove reference to tapping the bearing housing, or any of the incorrect fittings so as not to lead anybody else down the wrong path. you have to read...
  2. Replies
    10
    Views
    395

    turn over has only ever meant the first thing to...

    turn over has only ever meant the first thing to anybody that has ever tried to start an engine. it's never meant the second.
  3. i'm playing around with my impeller right...

    i'm playing around with my impeller right now...oddly enough, the best result has been with a 13/20 tweaked to 15/20...don't ask me why. lol.
  4. Replies
    14
    Views
    501

    Jesus. You need to video this! Heat up the...

    Jesus. You need to video this!

    Heat up the impeller.
  5. Replies
    8
    Views
    4,453

    Can you post a picture of where you mounted the...

    Can you post a picture of where you mounted the transducer? thx.
  6. diy intake, ribbon delete, jim's plate, 2 degree...

    diy intake, ribbon delete, jim's plate, 2 degree wedge, solas impeller, dean's 8600 tune.

    i'm guessing, retainers, intercooler, cooling mods, then can hit 85 mph easily @ higher rpm.
  7. without that middle bar, you're def going to suck...

    without that middle bar, you're def going to suck up more debris. the stock grate is a good top loader. i've put mine side by side with riva, and there really isn't any difference except for the...
  8. Replies
    6
    Views
    445

    why do you think that bearing housing seals can...

    why do you think that bearing housing seals can overheat, or that it needs to be cooled? it doesn't appear that there is any discernible amount of water circulation in that area aside from the fact...
  9. Replies
    31
    Views
    1,029

    The Y on My ski is installed quite far back. With...

    The Y on My ski is installed quite far back. With the stock exhaust in, I wouldn't be able to reach the valve if it was installed between the transom and the Y.

    Hence the added hose... Plus short...
  10. Replies
    3
    Views
    229

    Changed new battery (3 year old battery so...

    Changed new battery (3 year old battery so figured it was a good idea anyway), swapped out coil packs with a good ski. No change.

    Checking injectors next.

    Going to order the feelers to check...
  11. Replies
    31
    Views
    1,029

    Thanks. Interesting point. If there's water in...

    Thanks. Interesting point.

    If there's water in the actual exhaust, I typically blow that out along with the water box with a few revs after a ride.

    As for the water in the water jacket of the...
  12. Replies
    31
    Views
    1,029

    added some hose and installed the valve higher in...

    added some hose and installed the valve higher in the hull for easy access...the only issue is that there is supposed to be a self draining feature which I guess means the water in the engine drains...
  13. Always thought running the breather outside would...

    Always thought running the breather outside would be a good thing to do... You've inspired me for another project!
  14. Sticky: It's grease that's not under pressure so...

    It's grease that's not under pressure so shouldn't be a problem. You can put Teflon tape or thread sealant on it too to be sure.
  15. Sticky: If you have a tap and die set, just put the...

    If you have a tap and die set, just put the metric 6mm die on that alemite fitting that you bought... It's a bit tight but it's a very close thread so will work.
  16. Sticky: You can rethread that Alemite fitting to metric....

    You can rethread that Alemite fitting to metric. That's what I did.
  17. Replies
    31
    Views
    1,029

    Where are you?

    Where are you?
  18. Replies
    31
    Views
    1,029

    Logically that rating is for a closed valve....

    Logically that rating is for a closed valve. Probably not going to see that level of pressure when flushing or towing. When the ski is under way and hopefully the valve is open there should be close...
  19. Replies
    31
    Views
    1,029

    Yes, there is a version of a pump strainer that...

    Yes, there is a version of a pump strainer that adds an additional cooling line and it does install on top of the pump.

    As for hose routing, it's certainly possible to use the bilge hose, but then...
  20. Replies
    31
    Views
    1,029

    haven't started doing anything with the hoses...

    haven't started doing anything with the hoses yet...just finished re-sealing and bolting up the transom. letting that cure for a couple of days.

    what are you trying to do?
  21. Replies
    31
    Views
    1,029

    3/4 pex brass ball valve is fairly compact in...

    3/4 pex brass ball valve is fairly compact in size and will fit into the 5/8 hose.
  22. Replies
    31
    Views
    1,029

    Maybe that plastic one is the way to go... Cheap...

    Maybe that plastic one is the way to go... Cheap enough to replace once a year.

    Easier to scrape the silicone off at eye level. Haha. 461716
  23. Replies
    31
    Views
    1,029

    been looking for a good compact metal one. the...

    been looking for a good compact metal one. the brass ones need to add barbed fittings which make it fairly large, as well as the handle is big and not stainless.

    any suggestions for a good metal...
  24. Replies
    5
    Views
    707

    Do you remember what size bits you were able to...

    Do you remember what size bits you were able to use?
  25. And impeller looked normal?

    And impeller looked normal?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4