Search

Type: Posts; User: DanSVHO

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    35
    Views
    3,573

    thank you. Yea, always careful it is...

    thank you. Yea, always careful it is dangerous-this ski isn’t for a rookie rider. You can get into trouble real fast...
  2. Replies
    29
    Views
    2,034

    Exactly I remember when I experience at first I...

    Exactly I remember when I experience at first I didn’t know what it was but now that I know, I’m sure of what it is.
  3. Replies
    29
    Views
    2,034

    im with you on the incremental adjustments. I...

    im with you on the incremental adjustments. I think I have the power to turn a 13/20 to 9200 with a open nozzle. I guess I just have to try the fz nozzle first and see where my RPMs are. My bet is...
  4. Replies
    29
    Views
    2,034

    I don’t have a stock prop nor stock Venturi but...

    I don’t have a stock prop nor stock Venturi but I do
    have a stock fz Venturi on the way. I don’t know if i
    should throw stock nozzle on and keep prop and see what my RPMs are, or send out to dean...
  5. Replies
    29
    Views
    2,034

    ok. Haven’t ever heard of anyone using a 12/17....

    ok. Haven’t ever heard of anyone using a 12/17. Let’s let some
    prop gurus like jim chime in. I already ordered a Fz nozzle. I will order a new prop when I know what i should get as far as pitch.
  6. Replies
    29
    Views
    2,034

    Thank you for that informative reply. It makes...

    Thank you for that informative reply. It makes complete sense that low separation. Between leading and trailing should be kept at certain difference for maximum pump efficiency. I am wondering, what...
  7. Replies
    29
    Views
    2,034

    ok. 82-83mm inner diameter?

    ok. 82-83mm inner diameter?
  8. Replies
    29
    Views
    2,034

    understood, however wouldn’t changing the prop to...

    understood, however wouldn’t changing the prop to a 13/18 drastically decrease my RPMs without switching to the FZ nozzle?
  9. Replies
    29
    Views
    2,034

    ill give that a try. Thanks for the input. Shall...

    ill give that a try. Thanks for the input. Shall I get the L13 as well or no?
  10. Replies
    29
    Views
    2,034

    ok. Thanks for the input. So a stock nozzle bored...

    ok. Thanks for the input. So a stock nozzle bored out 2mm is the way to go? Along with a 13/18 pitch + L13 cone? Correct me if im
    wrong but, will I have to remove the Syphin in the nozzle when...
  11. Replies
    29
    Views
    2,034

    yea, it’s a 13/18 de-pitched to a 13/16 to keep...

    yea, it’s a 13/18 de-pitched to a 13/16 to keep RPMs up given the extended smaller nozzle. Only problem is with L13 I would rid of the stock Bilge syphin.
  12. Replies
    29
    Views
    2,034

    I believe it is what you described. However i...

    I believe it is what you described. However i sealed it Better than what the factory did. I would’ve hoped this would’ve eliminated it. I wish somebody could give me a tutorial on exactly where to...
  13. Replies
    29
    Views
    2,034

    I suppose it can be that bit it still feels...

    I suppose it can be that bit it still feels slower out of hole given a certain throtte
    input. If it felt the same as it did once in plane, then I would say it’s just resonation from exhaust and I...
  14. Replies
    29
    Views
    2,034

    2019 Fx svho, modded grate, Solas prop13/16, ...

    2019 Fx svho, modded grate, Solas prop13/16, extended Venturi smaller diameter, transom resealed.
  15. Replies
    29
    Views
    2,034

    Anyone experience this...

    Been driving me nuts and need to know if itís normal. Upon getting on plane the ski feels like pump is not efficient and it revs but doesnít accelerate as fast as you would expect given the amount of...
  16. Replies
    35
    Views
    3,573

    I did have the oem plate cut by him first. But It...

    I did have the oem plate cut by him first. But It would bounce at high speeds.
  17. Replies
    35
    Views
    3,573

    Sure. That makes sense. Well, I’m not sure I want...

    Sure. That makes sense. Well, I’m not sure I want to tinker with it more as it is running great now. If I had a stock nozzle, my RPMs would probably be 9800 and I wouldn’t be going faster. With the...
  18. Replies
    35
    Views
    3,573

    You have more power? What size wheel and do you...

    You have more power? What size wheel and do you have na cams as well?
  19. Replies
    35
    Views
    3,573

    well I have a extended nozzle that’s small and my...

    well I have a extended nozzle that’s small and my prop is pitched to 13/16 to compensate. I’m not sure I could get faster because I can’t Depitch more than 16?
  20. Replies
    35
    Views
    3,573

    I did several runs and they were all around that...

    I did several runs and they were all around that speed. The one I posted was just the highest. I did reach this in interacoastal with a slight chop. Less than a ft but it ripped right through. I feel...
  21. Replies
    35
    Views
    3,573

    this is only recommended if you experience...

    this is only recommended if you experience porpoising. Some hulls experience this, others do not. Also, the picture you show is of the oem plate. I have the older model Fx plate.
  22. Replies
    35
    Views
    3,573

    Yea. You have the original design using factor...

    Yea. You have the original design using factor stock 19+ plate. It’s doesn’t have the same material thickness so the cut cannot be that aggressive. Keep in mind I still have to shim the rear two...
  23. Replies
    35
    Views
    3,573

    not only faster but eliminates porpoising and...

    not only faster but eliminates porpoising and cuts through chop better. I was able to maintain some pretty high speeds through a thick chop comfortably. It’s the older style Fx plate used 2013-2018....
  24. Replies
    35
    Views
    3,573

    i think if the hull is setup right it is faster....

    i think if the hull is setup right it is faster. Deans newer plate cut also helped. He uses the old style plate and cuts that. It’s nice.
  25. Replies
    35
    Views
    3,573

    The low accuracy sign popped up when I stopped...

    The low accuracy sign popped up when I stopped after it recorded the highest top speed and while I took the screen shot. I did multiple runs anyway and they were all right around there.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4