Search

Type: Posts; User: thastinger

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    627

    Sooo, today I did manage to get one of the...

    Sooo, today I did manage to get one of the impellers off and the wear ring cut out...but the other one is still being stubborn.

    The one that won't come apart is the one with the suspect prop...
  2. Replies
    5
    Views
    627

    Need advice on 04 12F jet pumps

    So I have a matching pair of 04 12Fs. They have been salt water their entire lives. I bought them from the original owner, guy I knew, they had sat in a field for 5 years because he got cochlear...
  3. Replies
    41
    Views
    2,898

    I always just run premium fuel (93 here) in my...

    I always just run premium fuel (93 here) in my pair of 04 12Fs and have never had an issue. My local marina only has non-ethanol 87 so I can buy pump 93 for less than what that costs per gallon
  4. Replies
    17
    Views
    1,816

    that is detonation, I would check the part number...

    that is detonation, I would check the part number on the ECU and put new rod bearings on that rod at a minimum
  5. Replies
    17
    Views
    1,816

    I bought a pair of 04 12Fs from a guy I know, he...

    I bought a pair of 04 12Fs from a guy I know, he swore they were stored properly before they sat for 5 years. Long story short, one motor had water intrusion in all cylinders and motor was locked....
  6. Replies
    87
    Views
    23,432

    Probably none, I bought it so I could have an...

    Probably none, I bought it so I could have an actual air filter on the motor
  7. Replies
    87
    Views
    23,432

    I bought this for my 12Fs, probably the same. You...

    I bought this for my 12Fs, probably the same. You have to cut a bit off the pipe but it is easy to do and it has the fittling for the oil seperator canister in the main pipe. You throw most of these...
  8. Replies
    4
    Views
    843

    I would put a fuel pressure gauge on it, might be...

    I would put a fuel pressure gauge on it, might be that the newly connected fuel pump power clip isn't making full contact and not allowing the pump to fully deliver. Don't keep trying to "rev through...
  9. Replies
    2
    Views
    710

    Had to replace both of mine when I bought the...

    Had to replace both of mine when I bought the skies, which had been sitting for years...pretty sure I used these...
  10. Replies
    8
    Views
    1,079

    I ordered some that were for a Ninja ZX12 motor...

    I ordered some that were for a Ninja ZX12 motor and they fit my 04 12F. They didn't say they were Riva in the add but they were when they arrived...or at least I assume that R-rated=Riva
  11. I never reuse any gaskets or o-rings so that part...

    I never reuse any gaskets or o-rings so that part is up to you
  12. Full disclosure, I have 12F skies but I think...

    Full disclosure, I have 12F skies but I think this process is the same.
    I already had my intake manifold off when I removed my oil cooler, but there is just the center stud which the oil filter...
  13. Replies
    22
    Views
    2,908

    cool, nice to know it is GTG

    cool, nice to know it is GTG
  14. Replies
    12
    Views
    3,506

    take one side of the fuel line off the fuel rail,...

    take one side of the fuel line off the fuel rail, turn the key on and see if fuel runs out. Have you ever replaced the fuel filter on it?
  15. Replies
    2
    Views
    577

    Just to follow up in case anyone else is...

    Just to follow up in case anyone else is searching and finds this thread...the ZX12R plates from Driven Performance do fit.
  16. Replies
    2
    Views
    577

    STX12f AIS block off plates

    Hi,

    I have a pair of 04 STX12Fs and would like to find the AIS block-off plates for them. I had assumed they were the same as the ZX12R plates but I ordered some and they were to small. The place...
  17. It's a revival!

    It's a revival!
  18. Thanks for the update...but your original post...

    Thanks for the update...but your original post said the ski "Was doing something strange which you had not seen before"...I took this to mean it had ran properly in the past. If the cam timing was...
  19. Thread: 15f speeds

    by thastinger
    Replies
    25
    Views
    5,216

    I guess it depends on what you use it for. We...

    I guess it depends on what you use it for. We live on the Chesapeake Bay and it is rarely calm enough to use full throttle for any length of time so top speed isn't a concern of mine, however the Fs...
  20. does not fit the 12F correct?

    does not fit the 12F correct?
  21. Why can't you just seal it with RTV? Just a small...

    Why can't you just seal it with RTV? Just a small bead, not enough that it squezzes onto the ISC shaft when you bolt it together.
  22. Replies
    36
    Views
    3,233

    We have a pair of 04 12Fs, bone stock and plenty...

    We have a pair of 04 12Fs, bone stock and plenty fast for us. Change the oil, filter and plugs once a year and flush them after salt water. Couple hundred hours on each and the naturally aspirated...
  23. sounds like a vacuum leak, maybe start it and...

    sounds like a vacuum leak, maybe start it and spray some carb cleaner around to find the leak
  24. Replies
    22
    Views
    2,908

    It could very well be that this is the location...

    It could very well be that this is the location of the casting plug and it is weaker than the surrounding pipe but there isn't supposed to be a hole there.
  25. Replies
    22
    Views
    2,908

    I leave the plugs out of all the holes when I do...

    I leave the plugs out of all the holes when I do it. I'm interested to see if you have 2 adjacent cylinders with low numbers because that is a lot of water and shouldn't be able to get into all 4...
Results 1 to 25 of 60
Page 1 of 3 1 2 3