Search

Type: Posts; User: twoballscrewball

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. FS Polaris 780 SLT, Polaris 1050 SLTX, Triton WC-II Tandem Trailer

    I have a Triton tandem trailer and a pair of Polaris skis for sale. Ad links below. Currently up in the Poconos, but I could drag them home to south Jersey during the week if anyone wanted to look at...
  2. FS Triton Elite WC-II, New Axle and Hubs, South Jersey / Poconos

    I have a Triton tandem trailer and a pair of Polaris skis for sale. Ad links below. Currently up in the Poconos, but I could drag them home during the week if anyone wanted to look at them.

    ...
  3. Replies
    1
    Views
    70

    Nevermind, found it. Posting here for the next...

    Nevermind, found it. Posting here for the next guy who looks :)

    https://www.watcon.com/fuel-system/fuel-float/fuel-float-1
  4. Replies
    1
    Views
    70

    Fuel Tank Floats?

    Anyone still making / selling fuel tank floats? I got one a few years ago here, forgot from who, for my 780SLT. Need one now for my 1080 SLTX.
  5. Any harm in adding a switch to intentionally trigger limp mode?

    Hi all,

    Quick question. I have a 1996 SLT 780 and a 1997 SLTX 1050.

    I boat on a lake that gets very busy on some weekends. Wakes and the washing-machine effect get horrendous, and I'm not...
  6. Very timely post, as my throttle lever snapped...

    Very timely post, as my throttle lever snapped it's top half toward the end of my vacation last week, and I was able to keep it together for the rest of the trip, but was thinking of going with a...
  7. Quick hijack for a thank you to k447, again, I'll...

    Quick hijack for a thank you to k447, again, I'll be checking my 1997 tomorrow.
  8. Replies
    4
    Views
    1,058

    Little extra info, for the common questions I see...

    Little extra info, for the common questions I see about this boat:

    Carbs were removed, cleaned, rebuilt, and aligned to intake and resync'd. I am sure they are good.

    Do not know status of...
  9. Replies
    4
    Views
    1,058

    1997 SLTX 1050 Low End Carb Issue

    My 1997 SLTX1050 is running awesome. Only issue is that the low end only runs well if I run about 1/4 choke. Without the choke on, it will hesitate from a stop, die out. If I give it just...
  10. I think that's the way I'm going to go with it, a...

    I think that's the way I'm going to go with it, a couple of heavy straps hooked to the hull ribs.
  11. I did that. Even exoxy'ed it in. It pulled...

    I did that. Even exoxy'ed it in. It pulled out. Not a lot of material left there. And what is there, is brittle. :(
  12. Replies
    3
    Views
    606

    FS - Parts Where in NJ?

    Where in NJ?
  13. Not sure how fast the 1050 is, but I outran my...

    Not sure how fast the 1050 is, but I outran my wife on the 780, my son and I on the 1050 :)

    Definitely gotta figure out the low end. The two smaller jets said 55 and 58, wonder if I put them back...
  14. We're up at the lake and she's in the water....

    We're up at the lake and she's in the water. Pulling 6500 or 6600 RPM wide open with good response almost across the board. As long as she's moving she's doing great, if I let it sit for any longer...
  15. Went with these: ...

    Went with these:

    http://www.shopsbt.com/jetski/keihin-cdk2-carb-rebuild-kit-kawasaki-polaris.html
  16. I know the Mikunis need the factory kits with the...

    I know the Mikunis need the factory kits with the red anodized diaphragm button to work best. I grabbed the Kehein kits what were listed to fit the 1997 SLTX so hopefully they will work out. We...
  17. Anyone have any ideas, other than just...

    Anyone have any ideas, other than just fiberglassing the battery into the hull??? :D
  18. Petcock is clean and free. No junk or water in...

    Petcock is clean and free. No junk or water in the filter/separator. I'm pretty familiar with these boats, completely gutted, cleaned, and rebuilt the motor in my 96 780. Just not familiar with...
  19. Steve's Weekly Spring SLTX1050 Question - Carbs

    Got the jet pump sorted out on my 1997 SLTX 1050. New (used) 6-vane, impeller, and wear ring. Test rode today and there is no more cavitation or any pump issues. Very happy.

    Carb issue now....
  20. Here's what I'm dealing with. the front thread...

    Here's what I'm dealing with. the front thread is OK. The rear thread mount is split with material missing.

    http://i.imgur.com/YCYhJbm.jpg

    http://i.imgur.com/J4nkc3j.jpg
    ...
  21. Will do, at work tonight so I'll reply later...

    Will do, at work tonight so I'll reply later tonight with those.
  22. Just scored a nice stainless 6-vane stator with a...

    Just scored a nice stainless 6-vane stator with a 5131366 prop out of a Virage 1200 for $80. Both look to be in great shape.

    The prop in the boat was a 5131554, which I looked up and seems to...
  23. 1996 SLT 780 Battery Hold Downs Destroyed

    The raised bosses where the battery bolts thread into the hull on my 1996 SLT are shot. They are cracked and there is not much left of them. Was like that when I bought it so no idea what...
  24. Prop. How does the trailing edge get bashed up...

    Prop. How does the trailing edge get bashed up like that?

    http://i.imgur.com/GTD13OJ.jpg

    http://i.imgur.com/W9x1Hk1.jpg

    http://i.imgur.com/Zl3UGmg.jpg
  25. Here's the wear ring. scratches are light, like...

    Here's the wear ring. scratches are light, like from sand, no deep gouges but you can definitely feel them.

    Going to need new bearing seals. Hopefully bearings are ok.
    ...
Results 1 to 25 of 147
Page 1 of 6 1 2 3 4