Search

Type: Posts; User: seaya

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    496

    I Figured it out just went and took a look at the...

    I Figured it out just went and took a look at the ski again seems my friend had some else doing work and routed that line to the valve cover where it doesn’t belong it’s to go back to the air intake.
  2. Replies
    8
    Views
    496

    Ok I’ll do the wet test but what’s confusing is...

    Ok I’ll do the wet test but what’s confusing is I’m building enough pressure just cranking the engine without starting for 3 to 4 seconds to push a hard stream of oil out of dipstick and have seen...
  3. Replies
    8
    Views
    496

    Oil level good, no mod, compression...

    Oil level good, no mod, compression 120,120,110,100 no wet test done just got a lot of air blowing out of fitting that goes to head cover located by oil separator box next to air filter box
  4. One difference is the sho intercooler bracket,...

    One difference is the sho intercooler bracket, there are no bolt holes on the HO head to be mounted
  5. Replies
    8
    Views
    496

    Crankcase pressurizing

    I have a 2013 vxs that has pressure blowing up from the vent hose into the head cover causing oil to be pushed out of the oil dip stick and this While cranking the engine. I have good compression in...
  6. Replies
    2
    Views
    254

    Ok great thanks

    Ok great thanks
  7. Replies
    2
    Views
    254

    Difference between vxs and sho head

    Wondering if there is a difference between the vxs and sho heads?
  8. Replies
    4
    Views
    525

    Vx 110 engine rebuild

    Looking for labor price to rebuild Vx 110 engine, piston, rings, crank shaft bearing, connecting bearings,
  9. Thread: Floating ring

    by seaya
    Replies
    5
    Views
    1,064

    Yea I probably need to go to the gym more, that's...

    Yea I probably need to go to the gym more, that's not really working for me the new floating ring is longer and stopping 2mm short of groove for clip.
  10. Thread: Floating ring

    by seaya
    Replies
    5
    Views
    1,064

    Floating ring

    Having trouble pulling back floating ring by hand and I see two floating ring tools that are used for this job one by turning a bolt and one with an arm to pull back to retract can anyone tell me...
  11. Replies
    1
    Views
    887

    Ok figured out intake and exhaust from the cam...

    Ok figured out intake and exhaust from the cam sensor so just need how to align the dots
  12. Replies
    1
    Views
    887

    Timing marks on a 2010 stx15f

    I have a 2010 15f that was apart and putting back together. I see that the cams have one dot on one side and two on the other side and no indication of wich is intake and exhaust so how are the dots...
  13. Replies
    4
    Views
    692

    Ok great thanks almost bought a new shaft to end...

    Ok great thanks almost bought a new shaft to end up with the same results.
  14. Replies
    4
    Views
    692

    So your saying the shaft is effortless to pull...

    So your saying the shaft is effortless to pull out from the bearing unlike YAMAHA where the shaft is pressed into the bearing
  15. Replies
    4
    Views
    692

    Drive shaft and bearing

    Replacing the bearing for the driveshaft and noticed that driveshaft slips easy back and forth in the bearing is this normal or is there suppose to be a tight spot on the shaft
  16. Thread: 1300 guage

    by seaya
    Replies
    1
    Views
    439

    1300 guage

    Can I replace an 06 1300 guage with a 2003 or 04 guage?
  17. Replies
    3
    Views
    1,348

    Ok pulled engine and yes the coupler to the...

    Ok pulled engine and yes the coupler to the intermediate shaft was stripped thanks for the help
  18. Replies
    3
    Views
    1,348

    When spinning the engine coupler shaft is also...

    When spinning the engine coupler shaft is also turning but not engine could the shaft to the flywheel be broken
  19. Replies
    3
    Views
    1,348

    Sho 2012 engine coupler spinning free

    I have a 2012 Sho the engine starts but goes nowhere, I turned the engine coupler which spins but engine doesn't rotate is this an easy fix or do I need to replace the crank
  20. Replies
    23
    Views
    3,325

    Thanks for all the input on this problem and it...

    Thanks for all the input on this problem and it did turn out that all the injectors were stuck so I went ahead and changed them out both skis started up
  21. Replies
    23
    Views
    3,325

    Yes fuses are good ski swings over fuel pump is...

    Yes fuses are good ski swings over fuel pump is working there is spark and ejectors was the only thing not working. Remote security doesn't give you all of this thanks.
  22. Replies
    23
    Views
    3,325

    Well I'm working on them for a friend that bought...

    Well I'm working on them for a friend that bought them in the states and Where in the Virgin Islands. So just trying to figure if the solution is simple he bought the like 8 months ago and only had...
  23. Replies
    23
    Views
    3,325

    When I mentioned fail start I ment if I certaian...

    When I mentioned fail start I ment if I certaian permissive is not met it shuts down that circuite like oil to high or low maybe an unplugged connection like a slant detection switch shuts down the...
  24. Replies
    23
    Views
    3,325

    I will take another look at the battery voltage...

    I will take another look at the battery voltage don't want to believe all 8 injectors or bad.
  25. Replies
    23
    Views
    3,325

    Battery voltage was good

    Battery voltage was good
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4