Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    40
    Views
    3,975

    They need.to go.back in where they came from. The...

    They need.to go.back in where they came from. The shims set the valve lash. If you swap everything around then the lash should be checked adjusted.
  2. Replies
    3
    Views
    1,374

    Awesome! Not sure why I had that in my head....

    Awesome! Not sure why I had that in my head. Thanks Jerry.
  3. Replies
    2
    Views
    716

    If I recall correctly the NA blocks don't have...

    If I recall correctly the NA blocks don't have the oil galleries for a supercharger install.
  4. Replies
    3
    Views
    833

    Do you have the oil pump bolted on?? Pretty sure...

    Do you have the oil pump bolted on?? Pretty sure I recall thinking it was wierd until I out the oil pump on and it tightens up. There's a pin on the oil pump that holds it.
  5. Whizzing noise sounds like a boost leak. You can...

    Whizzing noise sounds like a boost leak. You can Rev it a bit out of the water if you got water hooked to the flush port. Just put in reverse to limit rpm in case you get carried away.

    Does the...
  6. Had my fzr repaired locally here in Vancouver...

    Had my fzr repaired locally here in Vancouver canada with no issues. if your desperate I'll try and get a hold of him.
  7. Replies
    66
    Views
    23,305

    Name the time and place and I'll ride it as fast...

    Name the time and place and I'll ride it as fast as it'll take my scrawny ass!
  8. Replies
    13
    Views
    4,839

    How they should have been built in the first...

    How they should have been built in the first place!!!
  9. Engine tech has a great product, if teaming up...

    Engine tech has a great product, if teaming up with riva is what it takes to get them more customers then all the power to them.

    Go canada go!
  10. Replies
    9
    Views
    1,192

    The problem is the lack off thrust bearings. Just...

    The problem is the lack off thrust bearings. Just a machined face in the center of the block with oil grooves. No replaceable bearings. When the jet pump or intermediate bearing fail they can put...
  11. Replies
    42
    Views
    5,361

    Some take more effort than others...

    Some take more effort than others...
  12. Replies
    4
    Views
    693

    Jerry tried it out, did a good right up on ita...

    Jerry tried it out, did a good right up on ita while back. Seemed to have good performance, but haven't heard much since. Might be a nightmare to find parts if it has problems.
  13. Thread: Lost rpms

    by Doug78
    Replies
    65
    Views
    4,296

    Check your blow off valve, be weary of the...

    Check your blow off valve, be weary of the clutch. A few have had them slip under load but not in the one way turn test.
  14. http://www.greenhulk.net/forums/showthread.php?t=2...

    http://www.greenhulk.net/forums/showthread.php?t=201166
  15. Replies
    2
    Views
    919

    JD 1 runs Molnar rods in his ski. Tom Molnar...

    JD 1 runs Molnar rods in his ski. Tom Molnar helped design the k1s before moving on to his own company. Search Molnar on the forum for more information.
  16. Replies
    2
    Views
    643

    There's a small screw on top of the supercharger...

    There's a small screw on top of the supercharger that is for priming the shaft with oil, check there. Then check the metal pipe that supplies the supercharger. Its goes from the front left side of...
  17. Just lucky the rods stayed together and didnt...

    Just lucky the rods stayed together and didnt ventilate the block...
  18. Replies
    20
    Views
    2,667

    I'm with ale, leave it stock and let it rip. I'm...

    I'm with ale, leave it stock and let it rip. I'm at war with mine now and have half a mind to sell it.
  19. Replies
    7
    Views
    2,496

    Heat for sure. I tried everything and when I...

    Heat for sure. I tried everything and when I finally got serious with the heat, it popped off with half the effort I was using before.
  20. Replies
    13
    Views
    3,088

    The biggest downfall as the lack of gel coat....

    The biggest downfall as the lack of gel coat. Otherwise unless your using it as a barge and crash into stuff it isn't a problem. Mine took a good hit and was repaired without issue, still good 100...
  21. Thread: Proper break in

    by Doug78
    Replies
    13
    Views
    1,254

    This is a rather contentious issue to discuss....

    This is a rather contentious issue to discuss. But gently is not the best way to break in the rings. Obviously getting the engine to operating temperature is the first step. Normally followed by a...
  22. Replies
    15
    Views
    1,324

    I was more referring to the hot cams valve shim...

    I was more referring to the hot cams valve shim kit. You might be ok just changing springs, worth checking your clearances and adjusting them while you are in there IMO. Mine where out to lunch, but...
  23. Replies
    27
    Views
    4,384

    I think the fz hull could get tweaked next year....

    I think the fz hull could get tweaked next year. As great the current hull is, i don't think it keeps up in closed course racing. So if Yamaha want to compete with the rxp-x then something underneath...
  24. Replies
    52
    Views
    5,149

    Lots of people blamed the Rd reflashes for...

    Lots of people blamed the Rd reflashes for blowing engine for a while. I think that often exists between the bars and the seat. No matter what the salesman say, you should be monitoring afr's, engine...
  25. Thread: JD1's FZR

    by Doug78
    Replies
    1,993
    Views
    339,759

    The cam set up will skew the boost numbers, that...

    The cam set up will skew the boost numbers, that head is going to make that ski a monster. Remember the sc doesn't create the pressure, only flow. Pressure is a result of resistance to flow.
Results 1 to 25 of 40
Page 1 of 2 1 2