Search

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Replies
    5
    Views
    266

    No. You can't not remove it. The oil pump feeds...

    No. You can't not remove it. The oil pump feeds the three carbs as well as the counter balance shafts at the front and rear of the motor.
  2. Replies
    87
    Views
    2,098

    Don't worry about it, I won't try to help you...

    Don't worry about it, I won't try to help you again.
  3. Replies
    87
    Views
    2,098

    Yes, I went back and looked. You mentioned that...

    Yes, I went back and looked. You mentioned that he was on vacation one time, back in post 32. Sorry, since you don't pay attention to us, I'm not paying close attention to you.
  4. Replies
    87
    Views
    2,098

    Just curious, if you have your own mechanic that...

    Just curious, if you have your own mechanic that knows all about these things, why are you here?
  5. Go ahead and re-use it, just keep an eye on it. ...

    Go ahead and re-use it, just keep an eye on it. It will likely fail sooner or later. Don't complain when you have to pull the engine again to change it.

    There are cheap ones on Ebay.
  6. A ZXi motor in an Ultra 150 hull would leave you...

    A ZXi motor in an Ultra 150 hull would leave you with a crappy Ultra.
  7. Replies
    16
    Views
    11,547

    Probably due to running with old gasoline with...

    Probably due to running with old gasoline with ethanol that absorbs water and forms crud in the carbs, causing them to run lean.
  8. Replies
    103
    Views
    5,056

    Hello Nikoli, i must say great write up. I'm...

    Hello Nikoli, i must say great write up. I'm currently doing the same swap on my 05 STX-R I just picked up last weekend. The good new for you and myself is i used to work for a level sensor...
  9. Replies
    14
    Views
    1,593

    Finally figured this out. Pulled the engine back...

    Finally figured this out. Pulled the engine back out to inspect lower end. I had the rear gear two splines off on the crank. But since you cover up the timing marks with the spacer and seal, i missed...
  10. Thread: A thank you

    by Khigh402
    Replies
    4
    Views
    461

    A thank you

    Today I took the ultra 150 for a test run before I took the carbs off. What do you know right back to 7000rpm which from what I read is perfect. It must have been the exhaust leak causing everything...
  11. Replies
    15
    Views
    3,199

    I have been getting PM's periodically from guys...

    I have been getting PM's periodically from guys with stuck Ultra-150 pumps, and since I moved on to other Model Kawasaki Jet-Ski's since the days of my Ultra-150 - I unfortunately can't help these...
  12. Replies
    2
    Views
    986

    Finally a USA trailer tire again

    Was shopping for my travel trailer and discover after 5 years you can finally get a good USA made trailer tire from Goodyear endurance brand. They cost more but I'm hoping they last as long as the...
  13. Replies
    120
    Views
    56,752

    Looking to do some bearing maintenance on my...

    Looking to do some bearing maintenance on my trailer. I found I can buy the complete hub assembly from Knott in Wisconsin. The assemblies are only $25 each, includes nut, seal and all. May be worth a...
  14. Replies
    2
    Views
    543

    run the right plugs the first time. you spent...

    run the right plugs the first time. you spent all that money rebuilding stuff and your gonna nickel and dime yourself on the little things?
  15. Replies
    10
    Views
    1,204

    So as not to damage the shaft, use a hydraulic...

    So as not to damage the shaft, use a hydraulic press. Most any auto shop, some parts stores, will have one and will do it for a minimal (if any) charge. I don't suggest using a hammer and vice as you...
  16. Replies
    41
    Views
    11,707

    Added hydro turf mats to the ultra. They came to...

    Added hydro turf mats to the ultra. They came to me with awful cut patterns. I had to razor blade and sand the corners to actually fit. They were long too. I love the way they look installed once I...
  17. Replies
    103
    Views
    5,056

    MFD ended up responding to the "new" speedo...

    MFD ended up responding to the "new" speedo sensor....

    I have a working dreameter! Or is it "Dreamometer"?

    Hahaha

    Going to 5200 the rear of the plug on the speedo sensor to waterproof tge...
  18. Replies
    23
    Views
    1,613

    now i have everything or close to connected. i...

    now i have everything or close to connected. i bleed my oil line to pump. but my next question is: i would crank the engine to full the fuel line to carb without spark plug cap. does it full the oil...
  19. Bolt the engine down, then glue in the bearing...

    Bolt the engine down, then glue in the bearing holder. That way it will be aligned.

    Best thing is to get the bolts snug, let the sealant cure, then tighten the bolts the rest of the way. That...
  20. Ultra 150 First run of the season with new mods

    So I got out for the first time yesterday after a long winter of tinkering on my 2000 ultra and Wow what a difference some of the mods have made!! I think the biggest difference was with the Jet...
  21. Replies
    38
    Views
    5,369

    Miami to Bimini!

    Our trip from Miami to Bimini! Total of 16 ski's. The crossing over was anything but easy, waves at a steady 4-6 feet, with occasional 8 footers. We were rewarded on the way home with calm seas,...
  22. I've had two major test runs to date. All the...

    I've had two major test runs to date. All the stalling and hard starting has all disappeared now. The engine idles perfectly and after running to my destinations and shutting down with the ski...
  23. Replies
    69
    Views
    3,843

    Ok update guys. Spent the afternoon at South...

    Ok update guys. Spent the afternoon at South Padre Island testing her out...results are in.

    It runs GREATTTTT! :)

    Im very happy with this bad mofo.

    This was day 2. Day 1 was cut short by a...
  24. Sticky: Wait until the day comes (if ever) that you have...

    Wait until the day comes (if ever) that you have to make a somewhat extensive repair on a four stroke ski that isn't covered under warranty. You'll know what true financial hemorrhaging is!!!
  25. Replies
    52
    Views
    3,021

    I got the part Turboman412,thanks again....im...

    I got the part Turboman412,thanks again....im installing it today....its getting to 65* :)
Results 1 to 25 of 57
Page 1 of 3 1 2 3