Search

Type: Posts; User: tchies

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    271

    FS - Parts Still lavailable and a 155 skat impeller

    Still lavailable and a 155 skat impeller
  2. Replies
    5
    Views
    188

    Thanks - one questions though - I was going to...

    Thanks - one questions though - I was going to fit the OEM sleeve - but the OEM had a taper cut into the back flat for the o ring - and the skat shaft is thinner - worried about the the pressure on...
  3. Replies
    8
    Views
    464

    sad part 2x $42.00 ouch

    sad part 2x $42.00 ouch
  4. Replies
    5
    Views
    188

    Help with jet pump shaft sleeve bushing

    3 bearing pump mod - the shaft sleeve that slides over the shaft into the oil seal is a bit worn. the other ones I have are a bit different and won't fit - anyone recognize this one. inside...
  5. Replies
    20
    Views
    692

    'E' is extended tip - 'C' - center tip - you can...

    'E' is extended tip - 'C' - center tip - you can use either or the older 300 ngk 4339 - I have used all - can't tell any difference. sometimes I think they make new ones to charge more.... nahhh
  6. Replies
    7
    Views
    465

    THat pipe would be easier - thanks for the tip

    THat pipe would be easier - thanks for the tip
  7. Replies
    7
    Views
    465

    After I used 2 1/2" rods to leverage the hat...

    After I used 2 1/2" rods to leverage the hat back and got the C clip out I couldn't get the shaft off the hat - or vice versa - mine was a PITA - used a block of wood under the shaft - took 2...
  8. Replies
    1
    Views
    110

    Purple wires are the power when on

    Purple wires are the power when on
  9. Replies
    4
    Views
    382

    cam timing on the 300's

    People use to retard the cam timing (rotate the cam gear within the slots allowed) on the 1500's - has anyone tried this on the 300's? Any consensus?

    Just curious.

    Ride on.. Tim
  10. Replies
    6
    Views
    262

    It will lock in place when place correct -...

    It will lock in place when place correct - usually long tab at about 11 oclock so you can see it with the pump installed
    put a little goop to secure it
  11. Replies
    20
    Views
    1,392

    I just used a pump from a 2008 RXP on the 2020...

    I just used a pump from a 2008 RXP on the 2020 RXTX 300 - bolted right up - I would assume the same pump alignment tool I used on the 2008 would work on my 2020?

    put the 15/25 159mm on my 2020 -...
  12. Replies
    20
    Views
    1,392

    My guess for the push up - would be more room to...

    My guess for the push up - would be more room to shim the motor - if needed - if it were at the bottom - you may not have the room to subtract shims - as long as you square up the motor - I don't...
  13. On my 2020 a 13mm socket and ratchet and one bolt...

    On my 2020 a 13mm socket and ratchet and one bolt will allow me to raise the gate - and hold it up with a zip tie - if needed. I can do from the ski. would be nice to have an easier way if it does...
  14. Replies
    1
    Views
    257

    2020 rxtx 300 boost number

    Installed a dash pac boost module - showed 12.9 psi on the dash - just an FYI - 110 hours. not certain where that compares to others

    Happy riding

    Tim
  15. BRp recommends replacement at 200 hours - many...

    BRp recommends replacement at 200 hours - many have gone much further.

    Good luck
  16. from 2020 manual Tim

    from 2020 manual


    Tim
  17. Replies
    106
    Views
    12,310

    Nothing to compare it to - I don't have the built...

    Nothing to compare it to - I don't have the built in butt dyno like others do....;-) or an acceleration meter - out by myself -- It always accelerates hard.

    I'll find out when I get to line up......
  18. Replies
    106
    Views
    12,310

    back from testing....... 2020 RXTX 300 110...

    back from testing....... 2020 RXTX 300 110 hours - Caloosahatchee River, Fort Myers 86+ degrees high humidity

    The ski is a bit faster with the 159mm 1+ to 2 mph. Both impellers were turning...
  19. Replies
    106
    Views
    12,310

    Should have my comparison once weather in Florida...

    Should have my comparison once weather in Florida clears - just got my ski back to normal - SC slip issue.

    Tim
  20. Replies
    0
    Views
    119

    map sensor crossover ?

    Bosch 0 261 230283 oem part number 420874656


    getting error P0106 - changed Throttle body - same issue - looking to swap map sensor

    Thanks

    Tim
  21. Replies
    0
    Views
    347

    SOLD 2018 Trinton LTWCI $850 Fort Myers

    SOLD
  22. Replies
    7
    Views
    854

    canadian firm now makes a two n one trailer - I'm...

    canadian firm now makes a two n one trailer - I'm picking one up this week in Fort Myers. I want it as it is easier to store the two singles in the garage vs a double - and i usually just take one...
  23. start the boat and watch that area

    start the boat and watch that area
  24. Thread: Blown 300

    by tchies
    Replies
    3
    Views
    533

    Mine did the same thing at 80 hours - BRP...

    Mine did the same thing at 80 hours - BRP replaced motor and Supercharger - no cost. never hurts to fight for it

    Best wishes
  25. Replies
    3
    Views
    301

    Quite a bit of water - 1/2+ cup - I'll have it...

    Quite a bit of water - 1/2+ cup - I'll have it tested properly though - 107 hours - super clean - occasional salt but always flushed.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4