Search

Type: Posts; User: Rodsatheart

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    28

    There are gel coat repair kits for small nicks...

    There are gel coat repair kits for small nicks and such. You also might get a hold of U S composites and see what they have. I've seen the repair kits on ebay and around the web, just can't remember...
  2. Replies
    2
    Views
    87

    I would take a measurement from the bed plate to...

    I would take a measurement from the bed plate to the end of the coupling, remove the plate from the engine, drop it in the hull and see how it sits.
  3. Replies
    23
    Views
    477

    Better than a broken rod going through the case. ...

    Better than a broken rod going through the case. :)
  4. Replies
    3
    Views
    127

    Are there any other lights coming on, like maybe...

    Are there any other lights coming on, like maybe the temp ? Have you reached down to test the temp of the water from the pisser, and how strong is the stream ? The Di's are common to the cooling...
  5. I'm assuming you know Mikuni makes 30, 60, and...

    I'm assuming you know Mikuni makes 30, 60, and 100psi popoff gauges ?
  6. Have you checked out the coils yet ? Plug wires...

    Have you checked out the coils yet ? Plug wires do age and break.
  7. Replies
    5
    Views
    141

    Sounds like there might be some crap in the...

    Sounds like there might be some crap in the metering circuit of one of the carbs or the inlet filters are restricted a bit.. Did it change at all when you turned them out ? Looks a tad rich on the...
  8. Replies
    11
    Views
    238

    The rubber diaphragm is the regulator. Don't star...

    The rubber diaphragm is the regulator. Don't star bending the needle arm to adjust pop off. Use springs. Put the springs that were in the carbs back in, and try using the old needles. The three...
  9. LMAO !!! It's amazing what I find getting these...

    LMAO !!! It's amazing what I find getting these used ski's. They had cut and connected wires together and wrapped with tape, I guess trying to fix a no start issue. Replacing the plastic nuts and...
  10. Replies
    11
    Views
    238

    Pop off should be 25. Use the spring that was in...

    Pop off should be 25. Use the spring that was in the carb. Jets are fine. Mixture screws should be at 1 turn out each. make sure the metal disk on the regulator diaphragm is facing the needle. DO NOT...
  11. The box on my 1100 was so bad when I got it, one...

    The box on my 1100 was so bad when I got it, one of the tabs on the rectifier was actually corroded off along with a wiring fiasco. Box was a mess. Had to rebuild the harness in the box....
  12. They know what they're doing, that's for sure.

    They know what they're doing, that's for sure.
  13. I did. Took it straight from Solas's catalog as a...

    I did. Took it straight from Solas's catalog as a stock replacement. I'll bet the pitch is off a tad. I know Impro's checks every impeller they sell per Dave.
  14. Replies
    6
    Views
    163

    Sounds like a voltage issue. Could be a bad...

    Sounds like a voltage issue. Could be a bad connection or rectifier.
  15. Replies
    1
    Views
    90

    I would it's 22 like most.

    I would it's 22 like most.
  16. Replies
    7
    Views
    185

    Put the original springs back in. Those springs...

    Put the original springs back in. Those springs will not get you 25psi pop off. It will be either to high or to low. Mat material was the fuel pump diaphragm made from ? Clear plastic or woven mesh...
  17. Don't ever think you shouldn't have bought the...

    Don't ever think you shouldn't have bought the ski. You like it, your learning, and I'm assuming enjoying doing it, and the hull appears to be in excellent shape (rare for the older ski's anymore)....
  18. Correct me if I'm wrong guys, but looks like that...

    Correct me if I'm wrong guys, but looks like that cyl ran lean.
  19. Replies
    0
    Views
    94

    zxi1100 cv carb specs

    http://greenhulk.net/forums/attachment.php?attachmentid=450755&stc=1
  20. If your not going to help the guy, and always be...

    If your not going to help the guy, and always be negative of what he is doing, don't open your mouth. He is evidently having fun doing it and learning. Why do 2 strokes suck ? I know of at least one...
  21. Replies
    9
    Views
    265

    If they are that bad, there are prob pin holes in...

    If they are that bad, there are prob pin holes in them and will prevent a vacuum from the pump. Replace it. And if they were that bad, I'm assuming there was a crap load of corrosion.
  22. Shafts are cheap (comparatively speaking). I...

    Shafts are cheap (comparatively speaking). I changed the one on my 1100 because it was bent. Not sure how, it was that way when I got it. Was easy to find because one blade was tight. Normally when...
  23. Sounds like it's over heating for whatever...

    Sounds like it's over heating for whatever reason. This should be up in the 4 stroke section for better coverage. Maybe a mod will move it for you.
  24. I have used Solas before on my ski's, and with...

    I have used Solas before on my ski's, and with proper clearance, yes there is a noticeable difference. KG-CD-15/21 would be the stock replacement Solas for your ski. If your getting a used pump, I...
  25. Replies
    9
    Views
    265

    While you have the pickup assy out, make sure the...

    While you have the pickup assy out, make sure the vent is clear. it should let air in the tank, but not out, and make sure the fuel return line is clear. Like Steve said, prob time to rebuild the...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4