Search

Type: Posts; User: bainer1290

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    127
    Views
    13,754

    Nice you did quite a few additions!!

    Nice you did quite a few additions!!
  2. Replies
    127
    Views
    13,754

    For sure, so what was the change(s) that got you...

    For sure, so what was the change(s) that got you there?
  3. Replies
    127
    Views
    13,754

    Nice work!!!

    Nice work!!!
  4. Replies
    127
    Views
    13,754

    Thanks for this I will set it up this way for the...

    Thanks for this I will set it up this way for the next time I go out to see if I can get a cleaner signal. Cheers!
  5. Replies
    127
    Views
    13,754

    Nice that will be a beast!

    Nice that will be a beast!
  6. Replies
    127
    Views
    13,754

    Good luck!!

    Good luck!!
  7. Replies
    127
    Views
    13,754

    Yes I have the original in its mount and a 2nd...

    Yes I have the original in its mount and a 2nd filter installed on the reserve pickup line zip tied to the original filter, so both are up high in the oem location
  8. Replies
    127
    Views
    13,754

    I removed the on off reserve valve and ran a dual...

    I removed the on off reserve valve and ran a dual pickup using the reserve pickup as the 2nd feed. There's some pics of my carb feed setup back a few pages in this thread basically I used a tee...
  9. Replies
    127
    Views
    13,754

    Nice, I used the osidebill recipe with F/A's and...

    Nice, I used the osidebill recipe with F/A's and chokes removed, starts great and throttle response is really good too. Mains 125 with 1-1/4 turns, Pilots 110 with 1 turn, 1.5 N/S and the 95g...
  10. Replies
    127
    Views
    13,754

    Got out on the water a couple more times, the GPR...

    Got out on the water a couple more times, the GPR is a beast. Did a couple speed runs today, just over half a tank of gas, slight chop of the water and was consistently doing 67-68mph. I suspect its...
  11. Replies
    127
    Views
    13,754

    Got out on the water today, was a bit of chop on...

    Got out on the water today, was a bit of chop on the lake and the water temp was cold but the GPR ran beautifully. Started right up, and ran great. Tried to vary the throttle and got about an hour of...
  12. Replies
    127
    Views
    13,754

    I'm hoping to get it on a lake this weekend if...

    I'm hoping to get it on a lake this weekend if the weather is half decent, fingers crossed!
  13. Replies
    127
    Views
    13,754

    Thanks!!

    Thanks!!
  14. Replies
    127
    Views
    13,754

    Started the engine today, it fired right up as I...

    Started the engine today, it fired right up as I primed the fuel lines and was able to use the primer. Now the weather just needs to warm up so I can take it for a test drive!!
  15. Replies
    127
    Views
    13,754

    Looking good!!

    Looking good!!
  16. Replies
    127
    Views
    13,754

    Finally got all the parts needed for the carb...

    Finally got all the parts needed for the carb rebuild, was waiting on the Mikuni kits, rejetted as per Bills specs 125 mains, 110 pilots, 1.5 N&S and 9g springs. Tested popoff for all 3 is in the...
  17. Replies
    127
    Views
    13,754

    Cool I used to have a 99GP1200 about 10 years ago...

    Cool I used to have a 99GP1200 about 10 years ago so looking forward to getting back into it. We go to BC and Montana lots well that was before covid but hopefully by next year that will be an option...
  18. Replies
    127
    Views
    13,754

    That makes sense more pressure in a triple. ...

    That makes sense more pressure in a triple.



    Thanks! I am in Lethbridge, the ski was from Med Hat but not sure on the history as it was in pieces when I found it... Should have it back on the...
  19. Replies
    127
    Views
    13,754

    Thanks Jonesfxr, that makes sense, I suspect my...

    Thanks Jonesfxr, that makes sense, I suspect my threebond on the seals would help some with that as well.
  20. Replies
    127
    Views
    13,754

    I did put threebond around the outer seal lips as...

    I did put threebond around the outer seal lips as I wanted to make sure they were sealed tight. What does the rest of this article show?
  21. Replies
    127
    Views
    13,754

    I don't think I have seen this before, whats the...

    I don't think I have seen this before, whats the full write up say?
  22. Replies
    127
    Views
    13,754

    Well good news the engine is now tight! Held 6psi...

    Well good news the engine is now tight! Held 6psi with no loss for 6 minutes, after 30 mins it was at 5.6psi, then at an hour 5.25psi.

    Next up a compression test then I will be dropping it back...
  23. Replies
    127
    Views
    13,754

    Thats good to know, I have no experience with the...

    Thats good to know, I have no experience with the copper spray.
  24. Replies
    127
    Views
    13,754

    Appreciate the advice! I tore it down and hit the...

    Appreciate the advice! I tore it down and hit the base gaskets and pv covers with 3bond. Hoping the next pressure test will be tight.
  25. Replies
    127
    Views
    13,754

    Question on pressure testing as I want to...

    Question on pressure testing as I want to clarify.

    I read the sticky http://greenhulk.net/forums/showthread.php?t=9408
    and the Group K article https://www.groupk.com/airleak.html

    One says the...
Results 1 to 25 of 69
Page 1 of 3 1 2 3